Bedienungsanleitung master DH 731 (Seite 22 von 60) (Alle Sprachen)

588482

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

4. Memory indicator

5. Water tank full indicator

6. Memory button

7. Humidity up button

8. Humidity down button

9. ON/OFF (power) button

► OPERATION

1. Plug the unit into a suitable mains socket (please refer

to the rating label on the backside of the unit to check the

appropriate voltage/frequency).

2. Press ON/OFF button to turn on the unit. When turning

on the unit for the rst time, if press only ON/FF button but

not set the Memory, the compressor will start (provided the

room humidity is higher than 50%).

3. Press the buttons Humidity up and Humidity down to

set the required humidity. The setting range is 40%~80%,

1% will be added or reduced for each press. The set hu-

midity will show on the LED display for 8 seconds, after

that the display will return to show the room humidity. Once

the set humidity is achieved, the compressor stops working

automatically.

Humidity range is 35%~95%, when the room humidity is

less than 35%, the LED display shows “LO”, when the

room humidity is higher than 95%, it shows “ HI”.

4. Press ON/OFF button again to turn off the unit.

5. When unit is turned on for the rst time or immediately

after shutoff, there is 3 minute delay protection for com-

pressor.

► MEMORY

By pressing Memory button, the memory indicator is on,

and the unit remembers the last settings.

► 6. DRAINAGE

Please note that in case the water tank is not positioned

appropriately, the water full indicator turns red. When the

water tank is full, the compressor stops, as a protective

measure, the “Water Tank Full” indicator turns red and

buzz.

To remove the water tank, pull it out carefully from the unit,

make sure it does not tilt over.

After empting the water tank, place the water tank into the

dedicated space. Make sure it is positioned properly, only

then the ’water full’ indicator is off and your dehumidier

can start working. (FIG. 5)

► CONTINUOUS DRAINAGE

When the dehumidier works in extremely high humidity

levels, the water tank requires more frequent drainage. In

this situation, it may be more convenient to set the unit up

for continuous drainage, according to the following proce-

dures:

► Remove the drain knob and rubber plug and retain for

future use.

► Connect the drain tube to the water outlet (FIG. 6) and

put the other end into a drain.

► 7. MAINTENANCE

Always unplug the unit from the mains supply before car-

rying out any maintenance or cleaning of the unit.

CASING CLEANING

Use soft cloth to clean the unit.

Don’t ever use volatile chemicals, gasoline, detergents,

chemically treated clothes, or other cleansing solutions as

they may damage the casing.

FILTER CLEANING (FIG. 7)

► Extract the lter from the unit.

► Use a vacuum cleaner or tap the lter lightly for easy

cleaning. If the lter is excessively dirty, use warm wa-

ter with a small amount of medium strength detergent.

► Make sure the lter is completely dry before installing

it back.

► Do not expose the lter to sunlight.

STORAGE

If the unit is not used for an extended period of time, please:

► Turn off the unit, unplug it and take away the AC cord.

► Empty the water tank completely and dry it.

► Cover the unit and store it in a place not exposed to the

direct sunlight.

► 8. TROUBLE SHOOTING

THE UNIT DOES NOT OPERATE:

► Is the unit plugged in?

► Is the house electricity on?

► Is the room temperature below 5

C or above 32

C? If

so, then it is out of the working range of the unit.

► Make sure the ON/OFF switch is turned on.

► Check if the water tank is positioned properly inside the

unit and if it is not full.

► Make sure the air inlet and outlet are not obstructed.

THE UNIT SEEMS TO DO NOTHING:

► Is the lter dusty, contaminated ?

► Is the air intake or outlet blocked?

► Is the room humidity already quite low?

THE UNIT SEEMS TO DO LITTLE:

► Are too many windows or doors open?

► Is there something in the room producing a lot of hu-

midity?

THE UNIT IS TOO NOISY:

► Check whether the unit is positioned on a level surface.

THE UNIT IS LEAKING:

► Make sure the unit is in appropriate condition.

► If you are not using continuous drainage, make sure

the rubber plug (on the bottom of the unit) is in its position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

master DH 731 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info