Bedienungsanleitung master DHA 10 (Seite 6 von 105) (Alle Sprachen)

588490

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

5. If an extension lead may become overloaded

6. Where the power cable may be damaged

7. On a slope or uneven surface

8. Where there is risk of re or close to a naked ame

9. Where it may be damaged by chemicals

10. Where there is a risk of interference by foreign objects

11. This product is not made for DIY repair

12. If there is a risk of water falling on the unit

► 

► FIG. 4

1. Air vent

2. Control panel

► FIG. 5

1. Handle of the unit

2. Air lter

3. Handle of the water tank

4. Drain of the tank

5. Cover of the water tank

6. Water tank

7. Drain hole for continuous drainage

8. Power cord

► FIG. 6

1. Dust lter

2. Active carbon lter

3. Filter xer

► 

1. MODE BUTTON

By pressing this button, you can set the working mode of

the machine to be:

LOW (MUTE dehumidifying):

When the ambient humidity < set humidity, the unit will run

in LOW fan speed (without Heater).

When the ambient humidity ≥ set humidity, the unit will run

in LOW fan speed & WITH Heater.

HIGH (TURBO dehumidifying):

When the ambient humidity ≥ set humidity, the unit will run

in HIGH fan speed & WITH Heater.

When the ambient humidity < set humidity, machine will

run in HIGH fan speed (without Heater).

DRYER: ALWAYS ON with HIGH fan speed and

HEATER.

2. HUMIDITY BUTTON

Press HUMIDITY button to set the room humidity you

need: continuous dehumidifying , 40%, 50%, 60% or 70%

The relative indicator will light on.

If the humidity button is not set, the unit will work in the

pre-set humidity: 50%..

3. TIMER BUTTON

Press TIMER button to set the working hours you desired.

As you press the button, the LED window will show the

number you chose (starting from 0, 1 to 24 in a cycle).

When the timer is activated, the TIMER Symbol would

light on and the setting time would appear 8 seconds on

the LED. After that, LED returns to room humidity again.

When the set time has been reached, the machine will

turn off automatically. If the timer button is not pressed,

the unit will work continuously for 24 hours.

4. POWER (ON/OFF) BUTTON

Press this button to start or turn off the machine. While the

power is on, the power indicator should light on.

5. MUTE OPERATION INDICATOR

While the MUTE function is chosen, this operation

indicator will light on.

6. TURBO OPERATION INDICATOR

While the TURBO function is chosen, this operation

indicator will light on.

7. CLOTHES DRYER OPERATION INDICATOR

While the CLOTHES DRYER function is chosen, this

operation indicator will light on.

8. HUMIDITY DISPLAY WINDOW

Display the room humidity (35~95%RH). While press

“TIMER” button, it shows the setting time, after 8 seconds,

return to room humidity.

9. HUMIDITY SETTING INDICATORS

continuous de-humidifying, 40%, 50%, 60%, 70%.

10. TIMER INDICATOR

Press this button to set the working time (1 to 24 hours).

11. POWER (ON/OFF)/CHECK INDICATOR

When the unit is in normal operation, this indicator will

light in blue. And, in the following conditions, the power

indicator will BLINK to warn you:

► The unit was tipped over.

► The fan is dissipating the heat (after the power is off,

the unit will keep dissipating the heat for 2 minutes to cool

down the unit).

12. WATER FULL INDICATOR

It turns to RED when water tank is full or the tank is not in

proper position.

► 

► Plug the unit into a correct mains socket. (Please refer

to the rating label at the rear of the unit.)

► Press button POWER to turn on the unit. The unit will

start to work in continuous mode.

► Press button HUMIDITY to set the room humidity you

need: continuous de-humidifying , 40%, 50%, 60% or 70%

► Press button MODE to choose the ventilation speed,

MUTE, TURBO or DRYER.

► Press button TIMER to set the working hour you need

(1~24 hours).

► To turn off the unit, press button POWER again.



► After switching off the unit, it takes at least 2 minutes

to OFF the unit completely, this allows the heater to cool

down. During the cool-down, the power indicator will blink

for warning.

     



























































Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

master DHA 10 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info