Bedienungsanleitung master DHP 45DV (Seite 7 von 72) (Alle Sprachen)

588470

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

In the “OFF” position the dehumidier never starts

(unipolar switch).

►5.2.HOUR COUNTER (2): The hour counter indicates

the number of hours of operation of the dehumidier.

►5.3.VENTILATION SPEED SELECTOR (3): The

ventilation speed selector allows the dehumidier to

work at the maximum air ow or at an intermediate air

ow depending on the need.

►5.4.ALARM LIGHT (4): The alarm light lights up when,

in case of dehumidier with tank, the tank is full or the

direct exhaust is clogged up and in case of dehumidier

with pump (optional), there is a malfunctioning in the

water discharge system. When the warning light comes

on the dehumidier does not work, reset the appliance

to restart it.

►5.5.REMOTE HUMIDISTAT SOCKET (5): If a remote

humidistat is connected to the socket, the relative

humidity you wish to achieve in the room may be

controlled remotely.

►5.6.VOLTAGE CHANGE SWITCH (6) (where present):

In dual voltage models (...DV), the dehumidier

operating voltage may be set to suit the voltage

supplied by the electricity mains.

►►6. SWITCH-ON

IMPORTANT: In dual voltage models (...DV), check:

►1-POSITION OF THE VOLTAGE CHANGE SWITCH

(220-240V / 110-120V) (Fig. 5); If the set voltage does

not match that supplied by the mains, the voltage

must be adapted. Loosen the two screws fastening

the cover (Fig. 6), move/press the switch on the

supplied voltage value (Fig. 7) and ret the cover

(Fig. 8).

►2-CHECK THE TYPE OF SOCKET; If the type of

socket does not match the power supply features, a

suitable adapter must be tted.

IF THE VOLTAGE CHANGE SWITCH POSITION,

THE TYPE OF SOCKET AND THE POWER SUPPLY

ARE CONSISTENT, YOU MAY PROCEED WITH THE

SWITCH ON SEQUENCE.

In order to start up the dehumidier, it must have

remained in vertical position (normal use position)

for at least eight hours. Failure to comply with

this rule may cause irreparable damage to the

dehumidier.

►6.1.Follow all the safety instructions;

►6.2.Connect the supply plug to the power mains (Fig. 9)

(SEE VOLTAGE IN THE “TECHNICAL DATA TABLE”);

►6.3.Turn the humidistat (1 Fig. 4) on the desired relative

humidity value, the dehumidier will start automatically.

Thanks to the “VENTILATION SPEED” selector (3 Fig. 4),

the dehumidier may be operated at the maximum air ow

or at an intermediate air ow depending on the need, in

order to achieve the utmost comfort in the room.

►►7. SWITCH-OFF

Proceed as follows to switch off the dehumidier:

►7.1.Turn the humidistat (1 Fig. 4) to “OFF“;

►7.2.Disconnect the supply plug from the power mains

with dehumidier off (Fig. 10).

►►8. REMOTE HUMIDISTAT CONNECTION

For remote humidistat ready models (5 Fig. 4), remove

the cover connected to the dehumidier and connect

the remote humidistat (optional) (Fig. 11). For correct

dehumidier operation, completely rotate the knob of the

humidistat on the control panel (1 Fig. 4) to “CONT“ and

set the desired humidity on the remote humidistat.

►►9. IF THE DEHUMIDIFIER DOES NOT

START OR DOES NOT DEHUMIDIFY

If the “ALARM LIGHT” (4 Fig. 4) switches on, this means

that the water recovery tank is full and/or there is pump

malfunctioning (optional), just empty the tank and/or

reset the pump. Should the problem persist, contact the

authorised technical service centre.

►►10. CONNECTION TO DISCHARGE PIPING

This dehumidier allows for the option to directly connect

the appliance to a xed discharge pipe.

►10.1.IN THE STANDARD CASE OF DEHUMIDIFIER

WITH TANK: The tank has a tting which may be

connected to a pipe with 16mm internal diameter. Before

connecting the pipe, remove the screw/cover (where

present) (Fig. 12) and check tting cleanliness, in order

to avoid possible obstructions.

►10.2.IN CASE OF DEHUMIDIFIER WITH PUMP

(OPTIONAL): A water drain pump (optional) may be

installed onto the dehumidier (Fig. 13). Connection is

easy and straightforward, thanks to the specic electrical

connector and the hydraulic tting located at the rear,

which can be connected to a pipe with 16mm internal

diameter. Before connecting the pipe, remove the

screw/cover (where present) (Fig. 14) and check tting

cleanliness, in order to avoid possible obstructions. ALL

INSTRUCTIONS AND DETAILS FOR INSTALLATION

ARE SUPPLIED IN THE PUMP KIT.

►►11. PERIODIC MAINTENANCE

The only maintenance to be performed regularly is

lter cleaning (Fig. 15). Cleaning must be performed by

removing the lter from the front of the dehumidier (Fig.

16) and placing it under the water tap in an ordinary sink.

This must be performed on average every month; in the

event of use in very dusty environments cleaning must be

more frequent.

Depending on use, cleaning of the nned coil may be

required, with a low pressure water jet. Before performing

washing it is strictly required to disconnect the supply plug

from the power mains (Fig. 10). To perform washing follow

the below steps (Fig. 17-18):

►11.1.Remove the screw that secure the cover to the

dehumidier (1);

►11.2.Rotate the cover (2);

►11.3.Remove the four screws and remove the protection

from the nned coil (3). (Wash the nned coil with a

low pressure water, paying attention not to wet the

electrical panel. WATER MUST ONLY FLOW FROM

THE TOP DOWN);

►11.4.Install the protection and the two screws (4);

►11.5.Rotate the cover to bring it back to a vertical

position (5);

►11.6.Install the screw than secures the cover to the

dehumidier (6).

Before restarting the dehumidier, ensure the electrical

parts are not wet and/or moist, in normal conditions at

least eight hours must elapse. This cleaning operation

improves the dehumidier performance and assures its

long life.



master DHP 45DV Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info