Bedienungsanleitung Master Lock LFW205FYC (Seite 4 von 8) (Englisch, Holländisch)

788782

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ENGLISH

Bolt-down instructions

(For select models only)

WARNING: Product is not water resistant once it is bolted

down. The ETL veriﬁed water resistance claim applies to product

prior to the application of a bolt-down kit.

Bolt-down kit contents (in select models only):

• 2 lag screws

• 2 washers

• 2 masonry anchors

Tools needed to bolt safe to the ﬂoor:

• Drill

• Wrench

• 7⁄16” (11 mm) drill bit – for drilling into the safe

• 9⁄32” (7.2 mm) drill bit – for drilling into a wood ﬂoor

• 3⁄8” (9.5 mm) drill bit – for drilling into a masonry ﬂoor

WARNING: • DO NOT drill from any location inside the safe.

• DO NOT bolt through the walls.

1 Tip the safe onto its right side (door hinges horizontal with the ﬂoor).

Unlock the safe and open the door.

Look to the bottom of the safe for

two indentations on the feet in

opposite corners. Using the 7⁄16”

(11 mm) bit; drill a hole through

each indentation perpendicular to

the bottom of the safe. DO NOT drill

from any location inside the safe.

3 Tip the safe upright, place the safe in the desired location and

open the door.

Use a screw or pencil to mark the ﬂoor

through both holes.

5 Move the safe aside to clear both marked spots for drilling.

6 Drill into the ﬂoor:

A For wood: Using the 9⁄32” drill bit, drill

a hole 2-1⁄2” (64 mm) deep in each

marked spot.

B For masonry: Using the 3⁄8” drill bit,

drill a hole 2-1⁄2” (64 mm) deep in each

marked spot. Install a masonry anchor

in each hole.

7 Replace the safe in the desired position, with the holes in the safe

aligned with those in the ﬂoor.

8 Securing the safe:

A For wood: Pass each lag screw through a

washer, then through the safe and into a

hole. Tighten with the wrench.

B For masonry: Pass each lag screw

through a washer, then through the safe

and into a masonry anchor. Tighten with

the wrench. Place masonry anchors into

the holes in the ﬂoor.

NOTE: • The safe should not be bolted to a wall, this will compromise

the ﬁre rating. Drill holes through the feet only. DO NOT drill

through the back or sides.

• Bolting/unbolting the unit is at the consumer’s expense and

discretion.

• Master Lock is not responsible for any costs incurred if the

unit is to be replaced.

Troubleshooting

THE PROBLEM: WHY IT IS HAPPENING: THE SOLUTION:

The door will not lock. 1. Shipping screw is in place.

2. Conﬁrm that there is no obstruction in the door.

3. Bolted down incorrectly.

1. Remove the screw on the back inside of the door.

2. Remove all items and accessories from inside the safe.

If this resolves the issue, re-set the accessories and

organize items to properly ﬁt.

The handle is not

in the horizontal

position when the safe is

locked.

The clutch mechanism has

been engaged.

Rotate the handle up or down until it clicks into the

horizontal position.

Cannot open door after

inputting the combination or

electronic code.

1. Safe doors equipped with a water-resistant

gasket may initially be tight.

2. Key lock is in the locked

position. (select models only)

1. Hold the handle up while inputting the code or dialing

the combination and then pull down on the handle.

2. If your safe is equipped with a key lock ensure that the

key is in the unlocked position. (select models only)

The dial does

not turn.

1. Shipping screw is still in place.

2. Locking bolts are not fully extended.

1. Remove the screw from the back of the door.

2. Ensure the handle is in the horizontal position.

Red indicator light blinks three

times and there are

three beeps.

An incorrect code has been entered. Verify code and re-enter. If the programmable code you

are using doesn’t work then use the factory code. If

successful re-program your programmable code.

Red indicator light blinks ﬁve

times and there are ﬁve beeps.

Keypad communication error. Visit masterlock.eu/safes

Red indicator light blinks once

and there is one beep.

Program button is pressed out of sequence.

-or-

5 seconds has lapsed between button entries.

Start over.

Red indicator light

is blinking.

An incorrect code has been entered three times

and system has entered delay mode.

Wait two minutes and start over.

Yellow indicator light is on. Battery power is low. -or- Battery may be the

wrong type.

Replace with new alkaline batteries.

Registration

masterlock.eu/safes

By registering your Master Lock product you can easily retrieve

forgotten codes, combinations or order new keys should they be lost.

Registering also ensures the best customer service should you have a

question or concern regarding your Master Lock product. By registering

your Master Lock product you can also be sure that in the unfortunate

circumstance of a ﬁre you will be guaranteed your replacement safe

(provided ofﬁcial paperwork).

Lifetime After-Fire

Replacement Guarantee

If your Master Lock product is in a ﬁre it will be sealed shut making

it necessary for it to be pried open. To help your family begin again,

Master Lock will ship a replacement free of charge. To be eligible for

the After-Fire Replacement Guarantee you (the original owner) must

Got a question?

If you ever have any questions regarding your Master Lock product,

please visit our website masterlock.eu/safes.

Master Lock LFW205FYC Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info