Bedienungsanleitung Mastercraft X46 (Seite 186 von 285) (Englisch)

614265

186

Zoom out

Zoom in

Vorherige Seite

1/285

Nächste Seite

Starting the Engine

Attach the emergency engine safety

switch tether (lanyard) to an article of your

clothing and to the switch.

All models will have a removable igni-

tion key. Its purpose is for safety and se-

curity. The key should be inserted prior to

starting an outing, and removed at the con-

clusion. This is intended to prevent theft or

unapproved use of the boat.

The process for starting the boat is:

• Insert the key and turn. This turns ON

the electrical system and prompts the

battery(ies) to provide power.

• Momentarily press the ENGINE

START-STOP button.

Note: While the engine is warming up,

check to see that all lights, video screens

and gauges operate properly. Check that

the steering system operates freely. There

should be no apparent leaks under pres-

sure. Re-engage the control lever after

warm-up by returning the lever to neutral

and pushing the throttle button back into

the engage position.

Shifting Gears

When shifting gears, always move the

control lever smoothly and quickly into

gear. Do not hesitate. Slow gear engage-

ment could damage the shifting mechanism

in the transmission.

NOTE: When shifting from forward to

reverse or reverse to forward, be sure to

stop the control lever in the neutral posi-

tion and allow the engine to fall between

600-800 RPM before completing the shift.

A one-hand, single-lever control operates

as both a gear shifter and a throttle. The le-

ver automatically locks in the neutral posi-

tion (straight up and down) for safety. The

lever can be moved from neutral only by

raising the lifter under the ball knob. Shift-

ing is accomplished by moving the lever

forward or backward. Center (straight up) is

neutral. Moving the lever forward engages

the running gear; moving it back from cen-

ter puts the drive train into reverse.

Never attempt to shift without the en-

gine running! This causes excessive wear

to the shifting mechanism and may nega-

tively affect control of the boat.

During regular warm-up of the engine,

it is possible to temporarily increase the

engine RPMs without moving the boat. To

accomplish this, push in the button locat-

ed at the bottom of the shift/throttle lever

with one hand and pull up the “umbrella”

(aluminum surround below the top of the

knob). Move the lever to desired position

and then simultaneously release the but-

ton and umbrella. The engine will run with

increased RPMs and can be increased or

decreased by moving the lever. Returning

the handle to the neutral position will bring

the system back to neutral and reduce the

engine RPMs to pre-set levels.

This function should be done sparingly.

Over-revving the engine for any extended

period can cause undue wear and tear on

the engine. Avoid advancing to wide-open-

throttle and holding the RPMs at that level.

Preparation • 2014 MasterCraft Owners Manual Page 5-11

P R E P A R A T I O N

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mastercraft X46 Seite 186

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info