Bedienungsanleitung Mastervolt GMDSS (Seite 4 von 20) (Englisch)

785585

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

SAFETY GUIDELINES AND MEASURES

2 SAFETY GUIDELINES AND MEASURES

2.1 WARNINGS AND SYMBOLS

Safety instructions and warnings are marked in this

manual by the following pictograms:

A procedure, circumstance, etc which

deserves extra attention.

CAUTION!

Special data, restrictions and rules with regard

to preventing damage.

WARNING

A WARNING refers to possible injury to the

user or significant material damage to the

charger if the user does not (carefully) follow

the procedures.

2.2 USE FOR INTENDED PURPOSE

1 The GMDSS Interface is constructed as per the

applicable safety-technical guidelines.

2 Use the GMDSS Interface only:

• In combination with a Mastervolt Mass series

battery charger

• in an approved application

• in a technical correct condition;

• in a closed, well-ventilated room, protected

against rain, moisture, dust and non condensing

circumstances;

• observing the instructions in the user’s manual

WARNING

Never use the GMDSS Interface in situations

where there is danger of gas or dust explosion

or potentially flammable products!

3 Use of the GMDSS Interface other than mentioned in

point 2 is not considered to be consistent with the

intended purpose. Mastervolt is not liable for any

damage resulting from the above.

2.3 ORGANIZATIONAL MEASURES

The user must always:

• have access to the user's manual;

• be familiar with the contents of this manual. This

applies in particular to chapter 2, Safety

Guidelines and Measures.

2.4 MAINTENANCE & REPAIR

1 If the GMDSS Interface and/or the Mass Battery

Charger is switched off during maintenance and/or

repair activities, it should be secured against

unexpected and unintentional switching on:

• Remove and tag out the fuse(s) from the AC

supply or;

• Switch off and tag out the AC circuit breaker;

• Switch off and tag out the connection with the

batteries and remove the fuses;

• Take adequate precautions to ensure that third

parties cannot reverse the measures taken.

2 If maintenance and repairs are required, use only

original spare parts.

2.5 GENERAL SAFETY AND INSTALLATION

PRECAUTIONS

• Do not expose the GMDSS Interface to rain, snow,

spray, moisture, excessive pollution and condensing

circumstances.

• Short circuiting or reversing polarity will lead to serious

damage to batteries, GMDSS Interface and the wiring.

Fuses between the batteries and the Interface can not

prevent damage caused by reversed polarity and the

warranty will be void.

• Protect the DC wiring with fuses, according to the

guidelines in this manual.

• Connection and protection must be done in

accordance with local standards.

• Do not work on the Interface or system if it is still

connected to a power source. Only allow changes in

your electrical system to be carried out by qualified

electricians.

• Check the wiring and connections at least once a year.

Defects such as loose connections, burned cables etc.

must be corrected immediately.

• Do not touch the equipment when wet or if your hands

are clammy.

• To open the cabinet of the Mass Battery Charger,

follow the instructions as stated in the user’s manual of

the battery charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mastervolt GMDSS Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info