Bedienungsanleitung Mastervolt Magic 12 24-10 (Seite 2 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

785628

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

Product description

The DC-DC converter MAGIC converts a DC-voltage into

another stabilized DC-voltage with a full galvanic isolation

between the input and output.

Applications

It offers you the following applications (see drawings

“INSTALLATION”):

MAGIC 24/12-20A (part no. 81300100)

• Drawing 1A, 1B: a stabilized 13.6V DC power supply

/ single stage float charger (e.g. to supply 12V

equipment from a 24V system), or

• Drawing 2A, 2B: a three-stage battery charger to

charge a 12V battery from a 24V system fully

automatically, or

• Drawing 3A, 3B: a 24/36 converter without galvanic

isolation, where the input is connected in series with

output.

• Drawing 4: a dimmer for 12V lights

MAGIC 24/24-20A (part no. 81300200)

• Drawing 1A, 1B: a 27.2VDC stabilized DC power

supply / single stage float charger (e.g. for a galvanic

isolation of the vehicle’s electrical system)

• Drawing 2A, 2B: a three-stage battery charger to

charge a 24V battery from a 24V system fully

automatically, or

• Drawing 3A, 3B: a 24/48V converter without galvanic

isolation, where the input is connected in series with

output.

• Drawing 4: a dimmer for 24V lights

MAGIC 12/12-20A (part no. 81300400)

• Drawing 1A, 1B: a 13.6VDC stabilized DC power

supply / single stage float charger (e.g. for a galvanic

isolation of the vehicle’s electrical system)

• Drawing 2A, 2B: a three-stage battery charger to

charge a 12V battery from a 12V system fully

automatically or

• Drawing 4: a dimmer for 12V lights.

MAGIC 12/24-10A (part no. 81300300)

• Drawing 1A, 1B: a 27.2V stabilized DC power supply

/ single stage float charger (e.g. for a galvanic

isolation of the 24V system), or

• Drawing 2A, 2B: a three-stage battery charger to

charge a 24V battery from a 12V system fully

automatically, or

• Drawing 3A, 3B: a 12/36V converter without galvanic

isolation, where the input is connected in series with

output.

Safety regulations and measures

1. Install the converter according to the stated

instructions.

2. Never use the converter at a location where there is

danger of gas or dust explosions.

3. Connections and safety features must be executed

according to the locally applicable regulations.

4. The converter may only be taken into operation while

the cover is closed as lethal voltages may exist.

The converter is provided with a non-replaceable input

fuse. If the plus and minus connections on the battery are

exchanged, the converter will become irreparable.

Do not use fuses larger than those indicated in the

specifications.

Installation

• Be sure that the output of the supplying source is

switched off during installation. Also be sure that no

consumers are connected to the batteries during

installation, to prevent hazardous situations.

• Check that the battery voltage is the same as the

converter’s input voltage (e.g. 24V battery for a 24V

input voltage). Also check that the output voltage

satisfies loading requirements

• Due to possible moisture accumulation and optimal

heat discharge, the converter must be installed in a

well-ventilated room protected against rain, vapour,

moisture and dust. We advise to mount the unit in a

vertical position with the connecting cables downward.

• Integrate a fuse in the positive wiring and place it

nearby the battery. See specifications for the

recommended fuse.

• Do not install the DC-DC converter straight above the

batteries because of possible corrosive sulphur

fumes.

Settings

There is no need to change the settings if the converter is

used as a stabilized DC power supply. Inside the

converter four DIP switches can be found to adjust the

converter according to your personal preferences. (see

table “DIP SWITCH SETTINGS”).

To adjust the DIP switches, proceed as follows:

1. Be sure the converter is disconnected from any

power source;

2. Remove the back cover of the converter by loosen

the four screws (see drawing “DIMENSIONS”);

3. Use a small flat-blade screw driver to change the

DIP-settings;

4. Remount the back cover again.

When more converters are paralleled to increase the total

output current, DIP-switches 1, 2 and 4 must be set to

the “OFF”-position and DIP-switch 3 depended to the

preferred output voltage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mastervolt Magic 12 24-10 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info