Bedienungsanleitung Mastervolt Mass Systemswitch 16 kW (Seite 12 von 20) (Englisch)

786811

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Mass Systemswitch 16 kW (230V) – User and Installation Manual

4.11 REMOTE PANEL (OPTIONAL)

See figure 8. If a Mastervolt remote control panel is

applied, you can fix the wires of the 10x0.5 mm² cable

from the remote panel to the remote control connector (ref

9 in figure 11) See also section INSTALLATION of the

manual of the remote control panel. These signals are

galvanically isolated from the mains grid.

Note: for an easy installation you can pull the screw

connector from the holder on the printed circuit board.

Function

- load on inverter

+ load on inverter

GND

U Generator

U shore

U inverter

System voltage

+ 12V power

GND

AC current

Figure 11: Pin configuration of the 10-pole connector to

the remote control panel

4.12 MASTERBUS (OPTIONAL)

See figure 8. The Mass Systemswitch can be connected to

the MasterBus network by means of the two data ports

(figure 8, reference 11). See also section 5.3 for details.

Note: For remote operation of the Mass Systemswitch

you have to choose between either the MasterBus

network or a remote panel as described in section

4.11. You cannot use both.

4.13 COMMISSIONING AFTER INSTALLATION

Follow the steps described below to switch on the Mass

Systemswitch.

1. Tighten all cable glands to ensure the pull relief.

2. Check all wiring and connections.

3. Close the front cover plate of the connection

compartment.

Note: If the gland plate was removed during installation,

be sure to slide back the cover plate before you fix

screws D and E (see figure 7).

4. Switch on the AC power sources.

Now the Mass Systemswitch is ready for operation.

4.13.1 MasterBus (optional)

During first commissioning the Mass Systemswitch will be

recognized by the MasterBus network automatically. The

remote control panel of the MasterBus network will

indicate that a new device was found.

The factory settings of the Mass Systemswitch are optimal

for most installations. In some applications however, it is

desirable to change settings. See section 6.3 for an

overview of all available settings. Refer to the user manual

of the remote control panel to change these settings.

Note: Some settings can only be changed via the

MasterBus interface. If changes were made to the

factory settings, all LEDs will flash three times

during powering of the Mass Systemswitch, i.e.

when either generator or shore input comes

available or when the MasterBus is powered.

4.14 DECOMMISSIONING

If it is necessary to put the Mass Systemswitch out of

operation, follow the instructions in order of succession as

described below:

1. Switch off all loads.

2. Switch off the AC power sources. These power

sources should be secured against unexpected and

unintended switching on.

3. Open the connection compartment of the Mass

Systemswitch (see paragraph 4.5).

4. Check with a suitable voltage meter whether the

inputs and the outputs of the Mass Systemswitch are

voltage free.

5. Disconnect all wiring.

Now the Mass Systemswitch can be demounted in a safe

way.

4.15 STORAGE AND TRANSPORTATION

When not installed, store the Mass Systemswitch in the

original packing, in a dry and dust free environment.

Always use the original packing for transportation. Contact

your local Mastervolt Service Centre for further details if

you want to return the apparatus for repair.

4.16 RE-INSTALLATION

To reinstall the Mass Systemswitch, follow the instructions

as described in section 4.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mastervolt Mass Systemswitch 16 kW Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info