Bedienungsanleitung Mastervolt Mass Systemswitch 16 kW (Seite 13 von 20) (Englisch)

786811

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Mass Systemswitch 16 kW (230V) – User and Installation Manual

5 MASTERBUS

5.1 WHAT IS MASTERBUS?

All devices that are suitable for MasterBus are

marked by the MasterBus symbol.

MasterBus is a fully decentralized data network for

communication between the different Mastervolt system

devices. It is a CAN-bus based communication network

which has proven itself as a reliable bus-system in

automotive applications. MasterBus is used as power

management system for all connected devices, such as

the inverter, battery charger, generator and many more.

This gives the possibility for communication between the

connected devices, for instance to start the generator

when the batteries are low.

MasterBus reduces complexity of electrical systems by

using UTP patch cables. All system components are

simply chained together. Therefore each device is

equipped with two MasterBus data ports. When two or

more devices are connected to each other through these

data ports, they form a local data network, called the

MasterBus. The results are a reduction of material costs

as only a few electrical cables are needed and less

installation time.

For central monitoring and control of the connected

devices Mastervolt offers a wide range of panels which

show full status information of your electrical system at a

glance and a push of a button.

New devices can be added to the existing network in a

very easy way by just extending the network. This gives

the MasterBus network a high degree of flexibility for

extended system configuration, not only today, but in the

future as well! Mastervolt also offers several interfaces,

making even non-MasterBus devices suitable to operate in

the MasterBus network.

5.2 EVENT BASED COMMANDS

With MasterBus each device can be programmed to

initiate an action at another connected device. This is done

by means of event based commands.

Example: if the shore power is almost in overload, the

generator must be started. As the shore power is

measured by the Mass Systemswitch, this device is

considered as the command source. The generator is the

device that should initiate an action (start the generator),

and is therefore considered to be the target. This means

that the Mass Systemswitch must be programmed as

follows:

Event

source:

Shore pre

overload

Select from list of events

sources (see Mass

Systemswitch manual)

Event

target:

Generator

Select from the device list

(devices connected to

MasterBus)

Event

command:

Status

Select event command from

the list of event commands of

the target (see Generator

manual)

Event

data:

Select event data from the

list of event commands of the

target (see Generator

manual)

See section 6.3.4 for the list of events sources and section

6.3.5 for the list of event commands of the Mass System-

switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mastervolt Mass Systemswitch 16 kW Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info