Bedienungsanleitung Mastervolt Solar ChargeMaster SCM20 PWM (Seite 13 von 16) (Englisch)

785623

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN / SCM20 & SCM40 PWM User’s Manual 13

3.8 COMMISSIONING AFTER INSTALLATION

CAUTION!

Check the polarity of all wiring before

commissioning: positive connected to positive

(red cables), negative connected to negative

(black cables).

1 If all wiring is OK, place the DC-fuse between the Solar

Chargemaster and the battery

WARNING

When placing this fuse, a spark can occur,

caused by the capacitors used in the Solar

Chargemaster. This is particularly dangerous in

places with insufficient ventilation, due to the

gassing of the batteries an explosion can occur.

Avoid having flammable materials close by.

2 Then. place the DC-fuse between the Solar

Chargemaster and the load.

3 The Solar Chargemaster will initiate the charging

process if the voltage from the PV array is sufficient.

If the Solar Chargemaster does not switch on,

press MENU shortly.

4 Refer to section 2.6 for settings.

3.9 DECOMMISSIONING

To put the Solar ChargeMaster out of operation, follow

these instructions in order of succession:

1 Switch off all loads that are connected to the Solar

Chargemaster;

2 Disconnect the PV array by switching off the switch

between the PV-array and the Solar Chargemaster (or

protect the PV-array from light exposure, e.g. by

covering the PV modules);

3 Remove the DC-fuse between the Solar Chargemaster

and the battery;

4 Remove the DC-fuse between the Solar Chargemaster

and the load;

5 Check with a suitable voltage meter whether the

Battery connection and the LOAD output of the Solar

Chargemaster are voltage free;

6 Disconnect the negative cable to the PV array from the

terminal block of the Solar Chargemaster. Isolate the

core of the wire with insulating tape;

7 Do the same for the positive cable to the PV array;

8 Disconnect all other remaining wiring.

Now the Solar Chargemaster can be demounted in a safe

way.

3.10 STORAGE AND TRANSPORTATION

When not installed, store the Solar Chargemaster in the

original packing, in a dry and dust free environment.

Always use the original packing for transportation. Contact

your local Mastervolt Service Centre for further details if

you want to return the apparatus for repair.

3.11 RE-INSTALLATION

To reinstall the Solar Chargemaster, follow the instructions

as described in this chapter (chapter 3).

3.12 CORRECT DISPOSAL OF THIS PRODUCT

(Waste Electrical & Electronic Equipment)

This product is designed and manufactured

with high quality materials and components,

which can be recycled and reused. When

this crossed-out wheeled bin symbol is

attached to a product, it means the product is

covered by the European Directive 2012/19/EU.

Please be informed about the local separate collection

system for electrical and electronic products.

Please act according to your local rules and do not dispose

of your old products with your normal household waste.

The correct disposal of your old product will help prevent

potential negative consequences to the environment and

human health

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mastervolt Solar ChargeMaster SCM20 PWM Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info