Bedienungsanleitung Matrix H3xe (Seite 19 von 24) (Englisch)

664295

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

BEFORE YOU BEGIN

LOCATION OF THE UNIT

Place the equipment on a level and stable surface away from direct sunlight.

The intense UV light can cause discoloration on the plastics. Locate your

equipment in an area with cool temperatures and low humidity. Please

leave a clear zone on both sides of the equipment that is at least 24”

(600 mm). This zone must be clear of any obstruction and provide the

user a clear exit path from the machine. Do not place the equipment in

any area that will block any vent or air openings. The equipment should

not be located in a garage, covered patio, near water or outdoors.

LEVELING THE EQUIPMENT

The equipment should be level for optimum use. Once you have

placed the equipment where you intend to use it, raise or lower one

or both of the adjustable levelers located on the bottom of the frame.

Use 6mm hex key through the access hole (shown below).

A carpenter’s level is recommended.

NOTE: There are only two levelers on the equipment.

WARNING!

Our equipment is heavy, use care and additional help if necessary when

moving. Failure to follow these instructions could result in injury.

POWER

If the equipment is powered by a power supply, the power must be plugged

into the power jack, which is located in the front of the equipment near the

stabilizer tube. Some equipment has a power switch, located next to the power

jack. Make sure it is in the ON position. Unplug cord when not in use.

WARNING!

Never operate equipment if it has a damaged cord or plug, if it is not working properly, if it has been

damaged, or immersed in water. Contact Customer Tech Support for examination and repair.

HYBRID SEAT HEIGHT

To adjust the seat height on the Hybrid Cycle, pull the orange lever under the seat and

lower the seat to the lowest position, stand over the seat and grab the orange lever. Pull

the lever and lift until the seat base makes contact with your pelvic bone.

RECUMBENT SEAT HEIGHT

To adjust the seat height on the Recumbent Cycle, locate the orange lever under the seat

before you mount the Cycle. Place your right hand on the orange adjustment handle

under the seat. Place feet on the ground while seated and slide forward if needed. Place

feet on pedals, gently lift lever under the seat. Using legs, slowly push and slide the seat

up or down to desired position. Release lever and allow to lock into place.

UPRIGHT SEAT HEIGHT

To raise the seat height on the Upright Cycle, pull the seat upward. To lower the seat,

locate the orange adjustment lever under the seat and pull the lever up to slide the seat

down. Release lever and allow to lock into place.

The seat height adjusts from level 1 to 23. Do not raise the seat past level 23.

FREE AREA

0.6 m

(2 ft)

0.6 m

(2 ft)

0.6 m

(2 ft)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Matrix H3xe Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Matrix H3xe

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info