Bedienungsanleitung Matrix T3x (Seite 11 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

664266

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

TENSIONING THE RUNNING BELT

After placing the treadmill in the position it will be used, the belt must be checked for

proper tension and centering. The belt might need to be adjusted after the first two

hours of use. Temperature, humidity, and use cause the belt to stretch at different rates.

If the belt starts to slip when a user is on it, be sure to follow the directions below.

1) Locate the two hex head bolts on the rear of the treadmill. The bolts are located at each

end of the frame at the back of the treadmill. These bolts adjust the rear belt roller.

Do not adjust until the treadmill is on. This will prevent over tightening of one side.

2) The belt should have equal distance on either side between the frame.

If the belt is touching one side, do not start the treadmill. Turn the bolts

counter clockwise approximately one full turn on each side. Manually center

the belt by pushing the belt from side to side until it is parallel with the

side rails. Tighten the bolts the same amount as when the user loosened

them, approximately one full turn. Inspect the belt for damage.

3) Start the treadmill running belt by pressing the GO buttion. Increase speed to 3

mph (~4.8 kph) and observe the belt position. If it is moving to the right, tighten

the right bolt by turning it clockwise ¼ turn, and loosen the left bolt ¼ turn. If it is

moving to the left, tighten the left bolt by turning it clockwise ¼ turn and loosen the

right ¼ turn. Repeat Step 3 until the belt remains centered for several minutes.

4) Check the tension of the belt. The belt should be very snug. When a person

walks or runs on the belt, it should not hesitate or slip. If this occurs, tighten

the belt by turning both bolts clockwise ¼ turn. Repeat if necessary.

NOTE: Use the orange strip in the lateral position of the side rails as criteria

to confirm the belt is properly centered. It is necessary to adjust the belt

until the edge of the belt is parallel to the orange or white strip.

WARNING!

Do not run belt faster than 3 mph (~4.8 kph) while

centering. Keep ngers, hair and clothing away from belt at all times.

Treadmills equipped with side handrails and front handlebar for user support and emergency

dismount, press emergency button to stop the machine for emergency dismount.

BEFORE USING THE TREADMILL

Perform initial setup and calibrate the treadmill using the auto-calibration

feature found in ‘Manager Mode’ or ‘Engineering Mode’.

NOTES:

• DO NOT stand on the belt while the auto-calibration sequence is in progress.

• DO NOT adjust incline until the initial setup and auto-calibration are completed.

• DO NOT start the treadmill running belt or press any speed buttons until directed to while tensioning the running belt.

BELT IS TOO FAR TO THE RIGHT SIDE BELT IS TOO FAR TO THE LEFT SIDE

TIGHTENS RIGHT SIDE OF ROLLER TIGHTENS LEFT SIDE OF ROLLER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Matrix T3x Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Matrix T3x

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info