Bedienungsanleitung Mavic Wintech Ultimate (Seite 4 von 26) (Englisch)

472808

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

4. INSTALLING THE SPEED SENSORS

4.1 E-Skewer

Fit the quick-release lever to the hub,

with the lever to the left (to the right

when using disc brakes).

Position of the locking lever

Adjust the tension on the adjusting

nut so that sucient force is applied

when the locking lever is moved to

the “CLOSE” position (consult your

retailer).

If the quick release lever can be

moved too easily to the CLOSE

position, there will be insucient

force holding the wheel. If this is the

case, place the quick release lever in

the OPEN position again and tighten

the adjusting nut to increase the force.

Then, push again the quick release

lever to the CLOSE position.

If too much force is needed to

move the quick release lever to

the CLOSE position, place the lever

in the OPEN position again, and

unscrew the adjustment nut to reduce

the force. Then, push again the quick

release lever to the CLOSE position.

Once the adjustment nut has been

set, the end of the quick release shaft

must not be sunk more than

2 mm in from the outside edge of the

adjustment nut.

Make sure the wheel is securely

tightened: raise the front wheel o

the ground and strike the top of

the wheel sharply in a downward

direction. The wheel must remain

rmly in place.

IMPORTANT:

At this point, your computer

is not yet ready to work. You

still need to set the necessary

programs, and then perform

the pairing operation of your

device.

4.2. E-Bolt

The speed sensor is integrated into a xing nut compatible with

all quick-releases on the market.

To install it, unscrew the xing nut on your quick-release.

Insert the quick release from the left-hand side of your bike and

tighten the electronic xing nut from the right-hand side.

Adjust the tightness of the nut according to the

recommendation described in section 4.1 of this user

guide.

4.2.1 Road bike

Once suciently tightened, position the sensor towards the

rear before closing the quick-release.

4.2.2. Mountain bike.

Once suciently tightened, position the sensor towards the top

before closing the quick-release.

IMPORTANT:

At this point, your computer is not yet ready to work.

You still need to set the necessary programs, and

then perform the pairing operation of your device.

4.3 Fork Sensor

To install the Fork sensor, the wheel magnet must be installed

rst. Read section 5 of this user guide rst.

Adjust the position of the speed sensor so the center of the

magnet is aligned with one of the arrows on the sensor. The

distance between the magnet and the sensor must be between

5 - 10 mm. 5.4 Tighten the wire tires and cut them ush.

IMPORTANT:

At this point, your computer is not yet ready to work.

You still need to set the necessary programs, and

then perform the pairing operation of your device.

OPEN

4.2.1

4.2

4.3

4.2.2

OPEN

4.1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mavic Wintech Ultimate Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info