Bedienungsanleitung Max SFX Series (Seite 18 von 133) (Englisch)

545558

Zoom out

Zoom in

Vorherige Seite

1/133

Nächste Seite

SFX SERIES USER’S GUIDE

Rev 2.2 16

After processing an input line (or after return is pressed on a blank line), the interface will display the “IDC>”’ prompt on

the terminal. You can type GetCommands at this prompt to obtain a list of available commands. Use upper and

lower case for the command as shown.

The terminal interface will remain active until an exit command is issued to logout, or the timeout period of five minutes

has been reached.

A separate International Datacasting Application Note is provided with details on the specific commands for the

Terminal Interface. Please proceed to Chapter 3 for more information on obtaining application notes.

Controlling the Receiver with the Web GUI

All accessible functions within the satellite receiver can be controlled using the Web Graphical User Interface (GUI).

The receiver acts as a web server in this case, serving out GUI pages to a PC with a browser. Communications

between the browser PC and the receiver is via a LAN connection to one of the Ethernet ports on the rear panel,

generally using the https protocol (SSL is used and the secure link is always enabled).

The Web GUI is compatible with the following web browsers:

1. Internet Explorer V5.0 or later, running under Windows® ‘95, ’98, 2000 or Windows NT or XP OS.

2. Mozilla V0.98 or later, running under Linux OS.

3. Firefox V1.5 or greater under Windows/Linux/MAC OS.

The Web GUI is best used with browsers that are displayed at a resolution of 1024 x 768 or greater, although 800 x

600 resolution is sufficient. However, at 800 x 600 resolution you may need to use the scroll bars more often.

Typically, an Ethernet crossover cable is used in the field when the receiver is being aligned to the satellite signal and a

point-to-point connection is required between the receiver and the browser PC. To communicate between the satellite

receiver and the browser PC, it is necessary that the IP address of the customer’s computer be set to the same subnet

as the receiver. The factory default IP address of the eth0 interface is 192.168.0.1 and the eth1 interface is

192.168.1.1. Typically, you will have to use the SetIP command in the Terminal Interface, or use the LCD control

panel to set the IP address to another value. If you do not know the IP address of the receiver, you can discover it by

using the GetIP command in the Terminal Interface, or you can view it through LCD control panel.

When the browser PC and the receiver are connected together via a hub or switch in a LAN configuration (typically

using Ethernet “straight through” cables), the same rule as above, applies.

If the browser PC and the receiver are on different LANs connected by the Internet, communications between the two

can only be made if the receiver IP address is known. Typically, the satellite receiver would be set up on its LAN with a

gateway to the Internet.

Once the receiver is set up with an IP address that is known, you can access the receiver by typing the IP address in

the Address line of the browser. The Web browser will default to port 443 (SSL), so only the IP address is required in

the Address line. If there is no demo content in the receiver (e.g. customized web page accessed in the clear via port

80), then this port will be forwarded through port 2100 (secure access). If your connection is successful, you will be

required to login to the receiver, as shown in the example Internet Explorer login page in Figure 1- 4 below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Max SFX Series Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info