545558
110
Zoom out
Zoom in
Vorherige Seite
1/133
Nächste Seite
SFX SERIES USER’S GUIDE
Rev 2.2 108
Important EMI & Safety Certification Information
Read these safety and operating instructions before operating your SFX series satellite receiver. Follow instructions
and heed all warnings on your unit and in this manual.
CAUTION: Equipment must be installed by a qualified service person and earth connection is
essential before connecting supply. Connect your power supply to a grounded AC outlet only.
Receiver Installation
Operate from a power source indicated on your receiver or in this manual.
The AC inlet is the main power disconnect. The socket outlet shall be near the equipment and shall be easily
accessible. The power requirements for this equipment are quite flexible with an acceptable power range of 100
to 240 VAC at 50 or 60 Hz. The fuse is part of the power supply. Replacement can only be accomplished by a
qualified technician.
Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them.
Be especially careful at plug-ins, convenience receptacles or cord exit points from the equipment. Frayed power
cords or damaged plugs are hazardous. Have them replaced by a qualified service technician. Overloaded wall
outlets and extension cords may cause fire or electrical shock.
Always ensure there is adequate ventilation when installing the equipment. Do not cover or block ventilation
holes. Doing so may damage the unit or cause a fire.
Avoid excessive humidity, sudden temperature changes or temperature extremes. Condensation may form inside
your unit.
To avoid costly damage or injury, place your unit on a solid, stable surface or mount in a rack free from vibrations.
Do not place any heavy objects on top.
Exterior Equipment Installation
Refer to the Figure 3 -1 while reading the instructions below.
Grounding the dish provides protection against static voltage build-up, which may damage equipment.
Grounding also provides some protection against surges induced by nearby lightning strikes. Any coax cable
that may be exposed to lightning or power conductors must have its outer shield grounded. There may be
additional grounding regulations in your area. It is important for you to consult and follow all the codes and
regulations in your area as you install your system.
The best method of grounding the outer shield of a coax cable is to use a ground block. This block is a barrel
connector to which you can install a ground conductor, such as a terminal, or a drilled hole and setscrew.
The terminal is where the outer conductor of the coax cable is attached to the grounding electrode. When
installed, the grounding block passes the LNB signal and DC voltages straight through while grounding the
outer conductor of the coax. One factor determining the ground block location is the location of an
acceptable ground electrode. The grounding conductor (the wire that runs between the ground block and the
110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Max SFX Series wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info