545558
118
Zoom out
Zoom in
Vorherige Seite
1/133
Nächste Seite
SFX SERIES USER’S GUIDE
Rev 2.2 116
Redundancy Option
If you have the Redundancy Option installed and enabled in your SFX series receiver, then this Appendix applies.
This appendix describes the operation of the Redundancy feature and the procedure for configuring the feature using
the Web GUI. The receiver can be configured for 1:1 redundancy, where there is one backup receiver per master
receiver or N for M redundancy, where several receivers can be backups for several other master receivers.
All redundancy configuration parameters can be setup using the Web GUI, Terminal Interface, or SNMP. Redundancy
cannot be configured using NetManager2. The Web GUI operation is described in this Appendix.
The redundancy feature is based on a proprietary IDC Equipment Redundancy Protocol (IDCERP), which is a
multicast IP protocol. This protocol has been in use in previous families of SRA and SFX series satellite receivers.
The master receiver (device) functions as a normal receiver, processing DVB packets and generating Sync/Async/Net
output. If redundancy is enabled, the master device also outputs Advertisement packets to announce itself to the
backup device(s). Only the master device generates LAN traffic (Advertisement packets). The Advertisement packets
are sent at a prescribed Advertisement interval, the trade-off being less LAN traffic vs. longer switch-over times. In
other words, the smaller the interval, the more often Advertisement packets are sent, and the faster the backup device
will switch to master status, due to a fault.
All backup device(s) are on the same LAN as the master device and must be of the same type and configuration as
the master. They also process incoming DVB packets, but have their output ports muted so that the data does not
collide with the data output by the master device. However, the backup device(s) do listen for Advertisement packets
from the master device.
A backup device will un-mute its ports and become a master if one of the following events occur:
1) the master device loses carrier lock;
2) the master device stops sending Advertisement packets;
3) the master device voluntarily gives up its master status.
Receivers with this feature enabled employ a filtering mechanism, based on a Device type and Group number.
Redundancy can be offered to devices of the same Device type, which belong to the same Group. For example, a
receive site could be configured with 4 receivers of the same type (e.g. SFX3101R) listening on two different carriers.
Since all receivers are of the same type, receivers 1 and 2 (master and backup for the first carrier) could be placed in
one group, and receivers 3 and 4 (master and backup for the second carrier) could be placed in a second group. This
would prevent receivers on one carrier providing redundancy for the receivers on the other carrier.
Appendix C
118

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Max SFX Series wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info