Bedienungsanleitung MaxGear MAX 5073 super bass system (Seite 2 von 28) (Deutsch, Englisch, Holländisch, Französisch)

506269

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

MAX 5073

Super Bass System

MOUNTING YOUR AMPLIFIER

The mounting position of your Amplifier will have a great effect on its ability to dissipate the heat

generated during normal operation. It has an ample heat sink for heat dissipation, and is also design-

ed with a thermal shut-down protection circuit, making it reasonably tolerant of mounting variations.

Any configuration which allows moving air to be directed over the cooling fins will improve heat dis-

sipation dramatically. DO NOT enclose the amplifier in a small box or cover it so that air cannot flow

around the heat sink fins.

Temperatures in car trunks have been measured as high as 175 F (80 C) in the summer time. Since

the thermal shut-down point for the Amplifier is 185 F (85 C), it is easy to see that it must be moun-

ted for maximum cooling capability. To achieve maximum advantage of convection air flow in an

enclosed trunk, mount the amplifier in a vertical position, on a vertical surface.

Cooling requirements are considerably relaxed when mounting inside the passenger compartment

since the driver will not often allow temperatures to reach a critical point. Floor mounting under the

seat is usually satisfactory as long as there is at least 1 inch (2,5cm) abo

ve the Amplifier’s fins for

entilation.

a. Select a suitable location that is convenient for mounting, is accessible for wiring, and has ample

room for air circulation and cooling.

b. Use the amplifier as a template to mark the mounting holes. Remove the Amplifier and drill 6 holes.

USE EXTREME CAUTION, INSPECT UNDERNEATH SURFACE BEFORE DRILLING.

c. Secure the Amplifier using the screws provided.

CONNECTING THE POWER

CAUTION! AS A PRECAUTION. IT IS ADVISABLE TO DISCONNECT THE VEHICLE’S BATTERY BEFORE

MAKING CONNCETIONG TO THE+12 VOLT SUPPLY WIRING.

10GAUGE (or a large gauge of wire if planning for additional Amplifiers) wire is recommend the power

and ground wires. 20 Gauge, for the remote turn-on wire. Both types are a

ailable at most Mobile

udio Dealers or installation Shops.

GROUND T

o V

ehicle Chassis

o avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be groun-

ded to a clean, bare, metal surface of the vehicle’s chassis.

NOTE: GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT.(1 METER)

USING THIS METHOD CAN CAUSE TURN ON AND TRUN OFF TRANSIENTS (NOISE)

+12 Volt (Fused)Constant Power: To Battery (+)

Due to the power requirements of the Amplifier, this connection should be made directly to the posi-

tive (+) terminal of battery. F

or safet

y measures, install an in-line 50 Amp Fuse Holder(not

included)as close to the battery positiv

e (+) terminal as possible, with an ampere rating not to exceed

the total value of fuses in amp.

Remote Turn-On Input: T

o P

ower Antenna output of Car Stereo

This Amplifier is turned “ON” remotely when the vehicle’s stereo is turned “ON”.

NOTE: IF YOUR RADIO DOES NOT HAVE A +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED

ON, “RMT” TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLE’S ACCESSORY CIRCUIT

THAT IS LIVE WHEN THE KEY IS “ON”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MaxGear MAX 5073 super bass system Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info