Bedienungsanleitung Maxicool Luna - LMD-AE-09HDI (Seite 23 von 35) (Englisch)

639706

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

 Page 23 

If you will install the unit on a wall-mounted

bracket , do the following:

CAUTION

Before installing a wall-mounted unit, make

sure that the wall is made of solid brick,

concrete, or of similarly strong material. The

wall must be able to support at least four

times the weight of the unit.

1. Mark the position of bracket holes based on

dimensions in the Unit Mounting Dimensions

chart.

2. Pre-drill the holes for the expansion bolts.

3. Clean dust and debris away from holes.

4. Place a washer and nut on the end of each

expansion bolt.

5. Thread expansion bolts through holes in

mounting brackets, put mounting brackets

in position, and hammer expansion bolts into

the wall.

6. Check that the mounting brackets are level.

7. Carefully lift unit and place its mounting feet

on brackets.

8. Bolt the unit firmly to the brackets.

TO REDUCE VIBRATIONS OF WALL-

MOUNTED UNIT

If allowed, you can install the wall-mounted

unit with rubber gaskets to reduce vibrations

and noise.

Step 4: Connect signal and power cables

The outside unit’s terminal block is protected by

an electrical wiring cover on the side of the unit.

A comprehensive wiring diagram is printed on

the inside of the wiring cover.

BEFORE PERFORMING

ELECTRICAL WORK,

READ THESE REGULATIONS

1. All wiring must comply with local and

national electrical codes, and must be

installed by a licensed electrician.

2. All electrical connections must be made

according to the Electrical Connection

Diagram located on the side panels of the

indoor and outdoor units.

3. If there is a serious safety issue with the

power supply, stop work immediately. Explain

your reasoning to the client, and refuse

to install the unit until the safety issue is

properly resolved.

4. Power voltage should be within 90-100% of

rated voltage. Insufﬁcient power supply can

cause electrical shock or ﬁre.

5. If connecting power to fixed wiring, install a

surge protector and main power switch with

a capacity of 1.5 times the maximum current

of the unit.

6. If connecting power to ﬁxed wiring, a switch

or circuit breaker that disconnects all poles

and has a contact separation of at least 1/8in

(3mm) must be incorporated in the ﬁxed

wiring. The qualiﬁed technician must use an

approved circuit breaker or switch.

7. Only connect the unit to an individual branch

circuit outlet. Do not connect another

appliance to that outlet.

8. Make sure to properly ground the air

conditioner.

9. Every wire must be firmly connected. Loose

wiring can cause the terminal to overheat,

resulting in product malfunction and possible

fire.

10. Do not let wires touch or rest against

refrigerant tubing, the compressor, or any

moving parts within the unit.

11. If the unit has an auxiliary electric heater, it

must be installed at least 1 meter (40in) away

from any combustible materials.

Outdoor Unit

Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Maxicool Luna - LMD-AE-09HDI Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Maxicool Luna - LMD-AE-09HDI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info