Bedienungsanleitung Maxicool Luna - LMD-AE-18HDI (Seite 19 von 35) (Englisch)

639708

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

6. Feed the signal wire through this slot, from

the back of the unit to the front.

7. Facing the front of the unit, match the wire

colors with the labels on the terminal block,

connect the u-lug and and firmly screw each

wire to its corresp onding terminal.

CAUTION

DO NOT MIX UP LIVE AND NULL WIRES

This is dangerous, and can cause the air

conditioning unit to malfunction.

8. After checking to make sure every conn ection

is secure, use the cable clamp to fasten the

signal cable to the unit. Screw the cable clamp

down tightly.

9. Replace the wire cover on the front of the

unit, and the plastic panel on the back.

NOTE ABOUT WIRING

Step 7: Wrap piping and cables

Before passing the piping, drain hose, and the

signal cable through the wall hole, you must

bundle them together to save space, protect

them, and insulate them.

1. Bundle the drain hose, refrigerant pipes, and

signal cable according to Fig. 4.15 .

Indoor Unit

Space behind unit

Refrigerant piping

Drain hose

Signal wire

Insulation tape

DRAIN HOSE MUST BE ON BOTTOM

Make sure that the drain hose is at the bottom

of the bundle. Putting the drain hose at the

top of the bundle can cause the drain pan

to overﬂow, which can lead to ﬁre or water

damage.

DO NOT INTERTWINE SIGNAL CABLE WITH

OTHER WIRES

While bundling these items together, do not

intertwine or cross the signal cable with any

other wiring.

2. Using adhesive vinyl tape, attach the drain

hose to the underside of the refrigerant pipes.

3. Using insulation tape, wrap the signal wire,

refrigerant pipes, and drain hose tightly

together. Double-check that all items are

bundled in accordance with Fig. 4.19 .

DO NOT WRAP ENDS OF PIPING

When wrapping the bundle, keep the ends

of the piping unwrapped. You need to access

them to test for leaks at the end of the

installation process (refer to Electrical Checks

and Leak Checks section of this manual).

Step 8: Mount indoor unit

If you installed new connective piping to the

outdoor unit, do the following:

1. If you have already passed the refrigerant

piping through the hole in the wall, proceed

to Step 4.

2. Otherwise, double-check that the ends of the

refrigerant pipes are sealed to prevent dirt or

foreign materials from entering the pipes.

3. Slowly pass the wrapped bundle of refrigerant

pipes, drain hose, and signal wire through the

hole in the wall.

4. Hook the top of the indoor unit on the upper

hook of the mounting plate.

5. Check that unit is hooked firmly on mounting

by applying slight pressure to the left and

right-hand sides of the unit. The unit should

not jiggle or shift.

6. Using even pressure, push down on the

bottom half of the unit. Keep pushing down

until the unit snaps onto the hooks along the

bottom of the mounting plate.

7. Again, check that the unit is ﬁrmly mounted

by applying slight pressure to the left and the

right-hand sides of the unit.

Fig. 4.15

 Page 19 

Indoor Unit

Installation

THE WIRING CONNECTION PROCESS MAY

DIFFER SLIGHTLY BETWEEN UNITS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Maxicool Luna - LMD-AE-18HDI Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Maxicool Luna - LMD-AE-18HDI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info