Bedienungsanleitung Maytag gc2227 (Seite 11 von 28) (Englisch)

346835

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

FreshFoodFeotures

Shelves

Your refrigerator has either Spillsaver TM or non-sealed

shelves. Spillsaver TM shelves have a spill retainer edge

which allows for easier clean up and some are

equipped with the EasyGlide TM slide out feature. To

slide out (select models), grasp the front of the shelf

and pull forward. Push in the shelf to return to the

original position.

To Remove a Shelf:

• Slightly tilt up the

front and lift up the

rear of the shelf, then

pull the shelf straight

out.

To Lock the Shelf Into Another Position:

• Tilt up the front edge of the shelf.

• Insert the hooks into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove drawers as indicated (see page 12).

• Place hand under the frame to push up the glass. Lift

glass out.

• To install, repeat above instructions in reverse order.

Elevator TM Shelf (select models)

The Elevator TM Shelf is equipped with a spill-retaining

edge and the EasyGlide TM slide-out feature. It can be

adjusted up or down without unloading.

To Slide Out Elevator TM Shelf:

• Grasp the front of the shelf and pull forward.

• Push the shelf in to return to original position.

To Adjust the Elevator TM Shelf:

• Pull out the knob on the crank handle.

• Rotate the crank clockwise to raise the shelf, and

counterclockwise to lower the height of the shelf.

To Remove Elevator TM Shelf:

• Completely unload the shelf and pull the shelf

forward.

Pull until the shelf stops.

Press up on the tabs located underneath its outside

edges and continue pulling forward until the shelf is

clear of the frame.

To Replace Elevator TM Shelf:

• Align the shelf to the frame and push it all the way

back. It is not necessary to press up on the tabs for

reinstallation.

In ordinary use, the Elevator TM Shelf frame assembly

does not require removal. Though unlikely, and not

recommended, the correct removal procedure is as

follows:

To Remove Frame Assembly:

• Unload the shelf completely.

• Slide the shelf forward about 5.1 cm and manually

move the two rear latches toward the shelf center.

• While supporting the entire shelf and frame from

underneath, lift slightly and rotate the assembly

approximately 30 ° to allow the rear mechanism to

clear the vertical rear side rails.

• The entire assembly can then be moved forward

and clear of the refrigerator compartment.

To Reinstall Frame Assembly:

• Reverse the removal procedure. Be sure the shelf

is in a level position. When the sliding shelf is

pushed to the rear, it will reposition the rear latches

to their correct operating position.

(style may vary)

Frame Assembly

Slide Out

EasyGlide '_Shelf

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Maytag gc2227 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info