Bedienungsanleitung McCulloch B33 PS (Seite 17 von 504) (Alle Sprachen)

684269

Zoom out

Zoom in

Vorherige Seite

1/504

Nächste Seite

To assemble the trimmer attachment

1. Attach the cutting attachment guard (A), braces (B),

washers (C), washers (D), and screws (E). Fully

tighten the screws. (Fig. 37)

2. Insert the hex wrench (A) to prevent rotation of the

shaft.

3. Remove the nut (B), support cup (C) and holder (D)

on the trimmer and brushcutter attachment. (Fig. 38)

4. Tighten the trimmer head (B) onto the shaft. (Fig. 39)

To assemble the brushcutter

attachment

1. Attach the cutting attachment guard (A), braces (B),

washers (C), washers (D), and screws (E). Fully

tighten the screws. (Fig. 37)

2. Insert the hex wrench (A) to prevent rotation of the

shaft.

3. Remove the nut (B), support cup (C) and holder (D)

on the trimmer and brushcutter attachment. (Fig. 40)

4. Attach the blade (B), bottom holder (C), support cup

(D), and nut (E). Fully tighten the nut. (Fig. 41)

To assemble the pole saw

attachment

See

To do the maintenance on the pole saw attachment

on page 20

for assembly instructions for the pole saw

attachment.

To assemble the two-piece shaft

1. Turn the knob to loosen the shaft coupling. (Fig. 42)

2. Move the locking/release button (A) into the guide

recess. Push the attachment into the coupler until

the locking/release button sets into the primary hole

(B). (Fig. 43)

3. Insert the shaft into the shaft coupling. The button

must go through the hole.

Note: If the attachment does not go fully into the

upper shaft, use the combination tool to push the

internal drive shaft deeper into the tube. It can be

necessary to turn the combination tool while you

push.

4. Make sure that you fully tighten the knob before you

operate the product. (Fig. 44)

To disassemble the two-piece shaft

1. Turn the knob to loosen the shaft coupling. (Fig. 45)

2. Push and hold the locking/release button (B). Pull

the shafts apart. (Fig. 46)

OPERATION

WARNING: Read and understand the safety

chapter before you operate the product.

Fuel

To use fuel

CAUTION: This product has a two-cycle

engine. Use a mixture of gasoline and two-

cycle engine oil. Make sure to use the

correct quantity of oil in the mixture.

Incorrect ratio of gasoline and oil can cause

damage to the engine.

Gasoline

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

CAUTION: Do not use gasoline with more

than 10% ethanol concentration (E10). This

can cause damage to the product.

• Always use new unleaded gasoline with a minimum

octane number of 90 RON (87 AKI) and with less

than 10% ethanol concentration (E10).

• Use gasoline with a higher octane number if you

frequently use the product at continuously high

engine speed.

Two-cycle engine oil

• Use only high quality two-cycle engine oil. Use only

an air cooled engine oil.

• Do not use other types of oil.

• Mixture ratio 50:1 (2%)

Petrol, litre Two-stroke oil, litre

5 0.10

10 0.20

15 0.30

20 0.40

860 - 001 - 28.10.2018 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch B33 PS Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info