Bedienungsanleitung McCulloch B33 PS (Seite 21 von 504) (Alle Sprachen)

684269

Zoom out

Zoom in

Vorherige Seite

1/504

Nächste Seite

2. Use the wrench to loosen the sprocket cover nut by

turning counterclockwise. Do not remove the nut.

(Fig. 66)

3. Use your fingers to tighten the nut against the cover.

4. Turn the adjustment screw clockwise until the saw

chain touches the bottom of the guide bar, then turn

the adjustment screw clockwise an additional ¼ turn.

(Fig. 72)

5. Use the screwdriver end of the combination tool to

move the chain around the guide bar. The chain

must move smoothly and freely. (Fig. 73)

6. If the chain does not move, it is too tight. Loosen the

sprocket cover nut and turn the adjustment screw

counterclockwise ¼ turn. Tighten the sprocket cover

nut.

7. Make sure there is not a gap between the chain and

the bottom of the guide bar. If there is a gap, the

chain is too loose and further adjustment is needed.

Do not operate the product if the chain is loose.

8. When the chain has the correct tension, lift the end

of the guide bar and firmly tighten the sprocket cover

nut clockwise with the combination tool. (Fig. 74)

(Fig. 75)

Note: The chain has the correct tension when it

moves freely around the guide bar, but it does not

hang below the guide bar.

To sharpen the chain

WARNING: Put on the gloves before you

sharpen the chain. Sharpen the chain from

inner side of the cutter to the outer side.

WARNING: Sharpen on the forward stroke

only. Use 2 or 3 strokes for each cutting

edge. Sharpen sufficiently to remove

damage to the cutting edges, which include

the side plates and the top plates of the

cutters. Keep all cutters at the same length.

Sharpen the chain when:

• The wood pieces decrease in size.

• The saw cuts to one side or at an angle.

• You must push the saw through branches with force.

1. Disconnect the spark plug.

2. Adjust the chain tension if it is necessary

To adjust

the chain tension on page 20

3. Set the file holder (A) to 90°. (Fig. 76)Make sure that

the file holder stays on the top edges of the cutter

(B) and the depth gauge (C).

Note:

The chain has left and right cutters.

4. Align the 30° file holder marks (A) with the guide bar

and to the center of the chain. (Fig. 77)

5. Sharpen the cutters (B) at one side. (Fig. 77) Turn

the chain around to sharpen the cutters at the other

side.

6. Examine the depth gauges and move them down.

Put the depth gauge tool on the cutters.

7. Make the depth gauge level to the top of the depth

gauge tool with the flat file.

8. Get a rounded front corner of the depth gauge with

the flat file. Make sure that the top of the depth

gauge is level.

To lubricate the guide bar and the chain

WARNING: Do not use waste oil. To use

waste oil can be dangerous to you and can

cause damage to the product and

enviroment.

The chain oil supplies continuous lubrication to the chain

and the guide bar. The oil output is automatically

monitored to make sure that there is sufficient oil. If

there is no sufficient oil, it will cause damage to the

guide bar and the chain, and too much heat. Too much

heat causes smokes in the chain and/or can change the

color of the guide bar. Always fill the bar oil tank when

you fill the fuel tank.

Obey these instructions to lubricate the guide bar and

the chain:

1. Stop the engine.

2. Remove the oil cap.

3. Fill the bar oil tank.

To do the maintenance on the guide bar

WARNING:

Do the maintenance on the

guide bar when:

• The product cuts to one side.

• You must push the product through with

force.

• The lubrication of the guide bar is not

sufficient.

After each operation, clean all sawdust from

the guide bar and the sprocket hole.

WARNING: Replace the guide bar when:

• The groove is worn.

• The guide bar bends or has cracks.

• The guide bar rails get too much heat

when you cut.

• Burrs occur to the guide bar rails.

It causes damage to the chain and becomes

not easy when you cut if the guide bar is

worn.

1. Disconnect the spark plug.

2. Loosen the clamp nut and remove the chain brake.

860 - 001 - 28.10.2018

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch B33 PS Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info