Bedienungsanleitung McCulloch Cabrio 433L (Seite 6 von 21) (Deutsch, Englisch, Französisch, Spanisch)

478383

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

INSTALLING TRIMMER

ATTACHMENT

WARNING: When installing attach-

ment, place the unit ona flat surface for stabil-

ity.

1. Loosen the coupler by turning the knob

counterclockwise.

Shipping

protector

Coupler

Knob

LOOSEN

TIGHTEN

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the attachment

(if present).

4. Position locking/release button of attach-

ment into guide recess of coupler.

5. Push the attachment int o the coupler until

the locking/release button snaps into the

primary hole.

6. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler

Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. All attach ments are designed

to be used in the primary hole unless otherwise

stated in the applicable attachment instruction

manual. U sing the wrong hole could lead to seri-

ous injury or damage to the unit.

Locking/Release

Button in Primary Hole

For optiona l a ttachmen ts, see th e ASSEMBL Y

section of the applicable attachment instruction

manual.

ATTACHING THE HANDLE

DANGER: To avoid serious injury, the

barrier po rtion o f the hand le must be installed a s

shown to provide a barrier between operator

and the spinning blade.

1. Position the loop handle on the shaft. Note

that the handle must be mounted between

the arrows on the shaft.

2. Install the bolt, securing plate and wing

nut as shown in the illustration.

3. Make a final adjustme nt of t hehandle to a

comfortable working position. Tightenthe

wing nut.

ASSEMBLY OF SHOULDER STRAP

Proper shoulder strap and handlebar adjust-

ments must be made with the engine com-

pletely stopped before using unit.

1. Insert your right arm and head throughthe

shoulder strap and allow it to rest on your

left shoulder. Make sure the hook is to the

right side of your waist.

NOTE: A one-half twist is built in the shoul-

der strap to allow the strap to rest flat on the

shoulder.

2. Adjust the strap, allowing the hook to be

about 15 cm below the waist.

3. Fasten the strap hook to the clamp located

between the trigger handle and the handle-

bar clamp base and li ft the t ool to t he operat-

ing position.

4. Try on shoulder strap and adjust for fit and

balance before starting the engine or be-

ginning a cutting operation.

NOTE: It may be necessary to relocate the

shoulder strap clamp on the shaft for proper

balancing of unit.

TO RELOCATE SHOULDER STRAP

CLAMP:

1. Loosen and remove both clamp screws.

2. Place the upper shoulder strap clamp

over the shaft.

3. Position the lower shoulder strap clamp

under the shaft and align the upper and

lower clamp screw holes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch Cabrio 433L Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info