478454
17
Zoom out
Zoom in
Vorherige Seite
1/564
Nächste Seite
STARTING AND STOPPING
English 17
1153988-26 Rev.3 2012-03-09
Starting and stopping
Cold engine
Starting: The chain brake must be engaged when the
chain saw is started. Activate the brake by moving the
front hand guard forwards.
(23)
Air purge:
Press the air purge repeatedly until fuel begins
to fill the bulb. The bulb need not be completely filled.
(26)
Choke:
Pull the blue choke/fast idle lever out to the full
extent (to the FULL CHOKE position). When the choke/
fast idle lever is pulled out to the full extent, the correct
throttle setting is set automatically.
(24)
Start throttle:
The correct choke/start throttle setting is
obtained by moving the control to the choke position.
(25)
Starting
Grip the front handle with your left hand. Hold the chain
saw on the ground by placing your right foot through the
rear handle.
Pull the starter handle with your right hand and pull out the
star
ter cord slowly until you feel a resistance (as the
starter pawls engage) then pull firmly and rapidly until the
engine fires.
Never twist the starter cord around your
hand.
(28)
CAUTION!
Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
Push in the choke control to the ”HALF choke” setting as
soon as the engine fires which can be heard through a
"puff" sound. (24)
Keep on pulling the cord powerfully until the engine starts.
As the chain brake is still engaged the speed of the engine
must be set to idling as soon as possible, this is achieved
by quickly pressing the throttle trigger once. This prevents
unnecessary wear to the clutch, clutch drum and brake
band.
(29)
Note!
Reactivate the chain brake by pulling the front hand
guard back (marked ”PULL BACK TO RESET”) towards
the front handle. The chain saw is now ready for use.
(30)
There is a simplified start reminder with illustrations
to describe eac
h step on the rear edge of the saw.
Warm engine
Use the same procedure as for starting a cold engine but
without setting the choke control in the choke position. Set
the throttle to the start position by pulling out the blue
choke control to the choke position and then pushing it in
again.
(27)
Never start a chain saw unless the bar, chain and all
covers are fitted correctly. See instructions under the
heading Assembly. Without a bar and chain attached
to the chain saw the clutch can come loose and cause
serious injury.
(31)
The chain brake should be activated when starting. Se
instructions under the heading Start and stop. Do not
drop start. This method is very dangerous because
you may lose control of the saw.
(32)
Never start the machine indoors. Exhaust fumes can
be dangerous if inhaled.
Observe your surroundings and make sure that there
is no risk of people or animals coming into contact with
the cutting equipment.
Always hold the saw with both hands. The right hand
should be on the rear handle
, and the left hand on the
front handle. All people, whether right or left handed,
should use this grip. Use a firm grip with thumbs and
fingers encircling the chain saw handles.
(33)
Stopping
Stop the engine by pressing down the stop button. (34)
!
WARNING! Note the following before
starting:
The chain brake must be engaged when
the chain saw is started to reduce the
chance of contact with the moving chain
during starting.
Never start a chain saw unless the bar,
chain and all covers are fitted correctly.
Otherwise the clutch can come loose and
cause personal injuries.
Place the machine on firm ground. Make
sure you have a secure footing and that
the chain cannot touch anything.
Keep people and animals well away from
the working area.
!
WARNING! Long term inhalation of the
engine’s exhaust fumes, chain oil mist
and dust from sawdust can represent a
health risk.
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

mcculloch-cs-380

Suche zurücksetzen

  • Wie Stelle ich die durchfließen gerne des kettenöls ein? Eingereicht am 20-3-2018 16:54

    Antworten Frage melden
  • Hallo
    meine Mcculloch CS 380 mit einer Klemmschraube und HEBEL zur Befestigung des Schwerts, hält die Kettenspannung nicht mehr.
    Habe alles gereinigt, aber nach ein paar Schnitten hängt die Kette wieder locker nach unten.
    Ich vermute, dass die Zahnräder keine Eigensicherung haben???
    Ersatzteil kaufen?
    Oder soll ich, bzw. kann ich umrüsten auf Zweimutternbefestigung?
    Gruß Karsten Eingereicht am 28-6-2017 10:43

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für McCulloch CS 380 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info