Bedienungsanleitung McCulloch Electramac (Seite 13 von 15) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

478435

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

ENGLISH - 10

and lower cut. The meeting point between the two

sides of the notch is called “directional cut line” This

line must be perfectly horizontal at right angles (90°)

to the felling direction.

The felling cut that provokes the tree fall, is performed

at 3 to 5 cm above the lower part of the directional

felling cut line, finishing at a distance of 1/10 of the

trunk from the notch. Remain on the left hand side of

the tree and cut using the chain pulling method and

the spiked bumper. Check that the tree does not

move in a direction other than that predicted for the

fall. As soon as possible insert a felling lever or

wedge into the cut. The uncut part of the trunk is

called the “hinge”, as it is intended to guide the tree

as it falls; in cases where the cuts are not sufficient,

not straight, or have been cut through completely, the

tree fall cannot be controlled (extremely dangerous!).

For this reason the various cuts must be performed

with great precision.

When cutting operations are completed the tree will

begin to fall. Where necessary help tree fall using

wedges or felling levers

Limbing

Once the tree has been felled, the trunk must be

limbed: in other words, the branches are removed

from the trunk. Do not underestimate this operation

because the large majority of kickback accidents

occur during this stage. For this reason pay close

attention to the position of the bar nose during cutting

operations and always work on the left hand side of

the trunk.

I. ENVIRONMENTAL INFORMATION

This section contains information useful for maintaining the characteristic of ecocompatibility included in the

origin design of the machine, and as regards proper use and disposal of chain oil

DESIGN

In the design stage, care was taken to develop an engine with reduced consumption and low emission of noise.

USE OF THE MACHINE

The operations of filling the oil tank should be carried out in such a way as to avoid spilling oil and contaminating

the soil and the environment.

DISPOSAL

Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized

organization for proper disposal in compliance with the regulation in force.

The symbol

on the product or on its packaging indicates that this product may not be treated as household

waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by inappropriate waste

handling of this product. For more detailed information about recycling of this product, please contact your local

council office, your household waste disposal service or the shop where you purchased the product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch Electramac Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info