Bedienungsanleitung McCulloch M3816 (Seite 13 von 17) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

478391

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

S Make your fist cut 1/3 of the way through

the bottom of the limb.

S Next makea 2ndcut all the way through

the limb. Then cut a third overcut leaving

a1to2inchc ollarfromthetrunkofthetree.

First cut

Second cut

Third cut

Collar

Pruning technique

SERVICE AND ADJUSTMENTS

WARNING: Improper maintenance

could r esult in serious engi ne damage or in se-

rious injury.

WARNING: Disconnect the spark

plug before performing maintenance, except

for carburetor adjustments.

We recommend all service and adjustments

not listed in this manual be performed by an

Authorized Service Dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level Before each use....

Bar lubrication Before each use.......

Chain tension Before each use.......

Chain sharpness Before each use....

For damaged parts Before each use..

For l oose caps Before each use......

For loose fasteners Before each use...

Fo r loose parts Before each use......

Inspect and Clean:

Bar Before each use................

Complete s aw After each use.......

Air filter Every 5 hours*.............

Chain brake Every 5 hours*........

Spark arresting screen

and muffler Every 25 hours*.........

Replace spark plug Yearly.

Replace fuel filter Yearly...

*HoursofOperation

AIR FILTER

CAUTION: Do not clean filter in gaso-

line or other flammable solvent to avoid

creating a fire hazard or producing harmful

evaporative emissions.

Cleaning the air filter:

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

1. Clean the cover and the area around it to

keep dirt and sawdust from falling into

the carburetor chamber when the cover

is removed.

2. Remove the parts as illustrated below.

3. Wash the filter in soa p and water. Rinse

in clean cool water. Air dry completely

before reinstalling.

4. Reinstall par ts.

Air Filter

Cylinder Co

Screws

Cylinder

Cover

BAR MAINTENANCE

If your saw cuts to one side, has tobeforced

through the cut, or beenrunwithanimproper

amount of bar lubrication it may be neces-

sarytoservice yourbar. A wornbarw illdam-

age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is

in the STOP position, thenclean all s awdust

from the guide bar and s procket hole.

To maintain guide bar :

S Move ON/STOP switch to the STOP posi-

tion.

S Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

S Clean the oil holes an d bar groove after each

5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Hole

S Burring of guide bar rails is a normal

process of rail wear. Remove t hese burrs

with a flat file.

S When railtopisuneven, use af latfiletor e-

store square edges and sides.

Correct GrooveWorn Groove

File Rail Edges

and Sides

Square

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch M3816 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info