Bedienungsanleitung McCulloch M4620 (Seite 8 von 19) (Englisch, Französisch, Portugiesisch, Spanisch)

478390

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Tighten

chain

Adjusting Wheel

Loosen

chain

3. Use a screwdriver to move chain around

guide bar to ensure all links are in bar

groove.

4. While lifting tip of guide bar, tighten bar

knob securely (clockwise). Hand tight-

en only!

TIGHTEN

5. Push lever on barknob downto returnle-

ver to closed/locked position.

WARNING: Failure to push lever on

bar knob down to closed/locked position

could result in serious personal injury or

damage to your chain saw.

6. Use a screwdriver to move chain around

guide bar.

7. If chain does not rotate, it is too tight.

Loosen bar knob 1 turn (counterclock-

wise); then, loosen chain by turning the

adjusting wheel

turn (upward direc-

tion). Retighten bar knob.

8. If chain is too loose, it will sag below the

guidebar. D O NOT operate t hesaw ifthe

chain is loose.

WARNING: If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

WARNING: M uffler is very h ot during

and after use. Do not touch the muffler oral-

low combustible material such as dry grass

or fuel to do so.

OPERATING YOUR UNIT

BEFORE STARTING ENGINE

WARNING: Be sure to read the f uel

information in the safety rules before you be-

gin. If you donot understandthesafety rules,

do not at tempt to fuel your unit. Con tact an

authorized service dealer.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too little oil will cause overheating

shown b y smoke coming from the chain and/

or discoloration of the bar.

Only use Bar and Chain Oil for bar and chain

lubrication.

Oil Cap

Fuel mix cap

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

This engine is certified to o perate on u nleaded

gasoline. Before operation, gasoline must be

mixed with a good quality 2-cycle air-cooled

engine oil designed to be mixed at a ratio of

40:1. A 40:1 ratio is obtained by mixing 0,125

liter o f oil with 5 liters of unleaded gasoline. DO

NOT USE automotive or boat oil. These oils

will cause engine damage. When mixing fuel

follow the instructions printed o n the container .

Always read and follow the safety rules relating

to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads

to separation and formation of acids during

storage.Ac idic gas can dam agethe fuel sys-

tem of an engine while in storage. To avoid

engine pr o blems, empty the fuel system be-

fore storage for 30 days or longer. Drain the

gas tank, start the engine and let it run until

the f uel lines and carburetor are empty. Use

fresh fuel ne xt season. Never use en gine or

carburetor cleaner products in the fuel tank

or permanent damage may occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch M4620 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info