Bedienungsanleitung McCulloch Mac542 E (Seite 7 von 9) (Englisch)

478413

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

ENGLISH - 5

Then open screw 1 full turn (counterclockwise) .

If acceleration is not smooth, open another 1/8 turn to

increase fuel flow .

• H: The needle screw H governs fuel flow at high speed

(throttle valve fully open).

To set hi speed screw H: close screw H turning it clock-

wise without forcing .

Then open screw 1 full turn (counterclockwise) .

If the engine speed is too high, open the screw about 1/8

turn (counterclockwise). Optimal adjustment is found

between 1 and 1 1/4 turns.

• I: The I (IDLE) screw controls the throttle opening to gov-

ern idle speed (2800 min

-1

) adjust as necessary.

CAUTION: increased idle speed may cause chain move-

ment.

The carburetor is adjusted for normal operation during pro-

duction. When considerable changes of altitude require a

supplementary adjustment, contact an authorised service

station which offers the latest in tools, parts and technical

assistance.

H. Routine maintenance

Ensure engine is always switched off before any kind of

maintenance operation.

CHAIN: Check tension regularly. A new chain will require more

frequent adjustment. Loosen retention nuts. Tighten chain (see

assembly instructions). Tighten retention nuts and adjust.

1 BAR

– Clean the bar groove (K) and check the lubrication holes

(L) in the bar to ensure that they are not clogged.

– Grease sprocket periodically. Rotate sprocket and

repeat.

– Rotate bar periodically to maximise bar life.

2 AIR FILTER

– A dust clogged air filter may cause carburetor problems.

This may prevent the engine from reaching its maximum

r.p.m. and cause high fuel consumption.

– Remove cover.

– Wash filter in petrol (do not use fuel which is mixed with oil).

– The filter can also be cleaned with compressed air.

– Replace filter if damaged or if it does not seal tightly in

the air box.

3 SPARK PLUG

Remove and clean the spark plug every 30 hours. Check

the electrode gap (0,5/0,6 mm. - 0.025 inches).

– Replace spark plug about every 100 working hours or

whenever it is extremely encrusted.

– Heavily encrusted electrodes can result from an incorrect

carburetor setting or from wrong fuel mixture (too much oil in

the fuel mix) or a poor quality of oil in the fuel mix. Check and

correct.

4 OIL FILTER

The oil filter is on the end of the oil suction hose inside the

oil tank.

To clean and replace the filter pull it out through the oil tank

filter opening. Use a piece of bent wire or long forceps.

To remove deposits from the oil tank half-fill it with

kerosene or petrol and shake thoroughly. Drain off and fill

the tank with fresh saw chain oil.

Never use waste oil.

5 FUEL FILTER

To change fuel filter remove the tank cap and pull out the

filter with a piece of bent wire or long forceps. Replace the

filter as shown in the illustration and reposition it. It is rec-

ommended to replace the fuel filter at least once a year.

CHAIN BRAKE

– WARNING: Contact your service dealer if anything

appears wrong with your chain brake. Do not disassem-

ble or manipulate the mechanism of the chain brake.

– Clean the brake mechanism periodically (without disas-

sembling it) and control the wear of the band visually.

• PERIODICALLY: It is important to clean the saw thor-

oughly particularly around cylinder fins to avoid over-

heating of the engine.

• LONG STORAGE: Empty fuel and run engine until dry.

I. Safety chain brake

Your chain saw is fitted with a safety chainbrake

designed to stop the chain in milliseconds in case of

kickback. Always hold the saw firmly in both hands.

The chain brake does not provide a total protection if the machine

is used without taking the necessary precautions and mainte-

nances.

The chain brake is intended to engage automatically in case of

kickback.

The chain brake can also be engaged manually by pushing

the chain brake lever forwards.The manual use of the chain

brake is recommended only at idle.

Always test the chain brake before using your saw. Do this by

engaging the brake at idle (see below).

Always release the brake before starting.

Kickback may occur if the end of the bar (see illustrated

angle) touches any solid object.

Never attempt to start a cut with the end of the bar.

Kickback is a violent upward and rearward movement of the

bar and may cause you to lose control of the machine.

Therefore you should avoid starting a cut with this part of the

bar. Always keep a firm grip on the saw with both hands

because, in case of kickback, it is the contact of the left hand

with the brake lever which will help to engage the brake.

CHAIN BRAKE TESTING:

1 The chain brake (A) is disengaged when brake lever is

pulled back and locked(chain can move).

2 The chain brake (A) is engaged when brake lever is in the

position (chain cannot rotate).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch Mac542 E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von McCulloch Mac542 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info