Bedienungsanleitung McCulloch Mac742 (Seite 8 von 17) (Deutsch, Englisch, Französisch, Spanisch)

478387

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Clutch

Cover

Lower

Hole

Guide Bar

Adjusting Pin

12. Install bar nuts and finger tighten only.

Once the chain is tensioned, you will

need to tighten bar nuts.

CHAIN TENSION (Including units

with chain already installed)

WARNING: Wear protective gloves

when handlingchain. The chain is sharp and

can cut you even when it is not moving.

NOTE: When adjusting chain tension,

make sure the ba r nuts are finger tight only.

Attempting to tension the chain when the bar

nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move chain around

guide bar. If the chain does not rotate, it istoo

tight. If the chainis tooloose, itwill sagbelow

the bar.

Chain Adjustment

Tool

(Bar Tool)

Guid

Bar

Adjusting

Screw

Bar Nuts

Adjusting the tension:

Chain tension is very important. Chains

stretch during use. This is especially true

during the first few times you use your saw .

Always check chain tension each time you

use and refuel your saw .

1. Loosen bar nuts until they are finger tight

against the clutch cover.

2. Turn adjusting screw clockwise until chain

solidly contacts bottom of guide bar rail.

Adjusting

Screw

3. Using bar tool, roll chain around guide bar

to ensure all links are in bar groove.

4. Lift up tip of guide bar to check for sag.

Release tip ofguidebar,then turnadjust-

ing screw

turn clockwise. Repeat un-

til sag doe s not exist.

Adjusting Screw --

Turn

5. While lifting tip of guide bar, tighten bar

nuts securely with the bar tool.

Bar Nuts

6. Use the screwdriver end of thebar tool to

move chain around guide bar .

7. If chain does not rotate, it is too tight.

Slightly loosenba r nutsand loosenchain

by turning the adjusting screw

turn

counterclockwise. Retighten bar nuts.

8. If chain is too loose, it will sag below the

guidebar.DO NOT operate thesaw if the

chain is loose.

WARNING: If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

WARNING: Muf fler is very hot during

and after use. Do not touch the muffler or al-

low combustible material such as dry grass

or fuel to do so.

OPERATING YOUR UNIT

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you donot understand thesafety rules,

do not attempt to fuel your unit. Contact an

authorized service dealer.

BAR AND CHAIN LUB RICATION

The bar and chain require continuous lubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too little oil will cause overheating

shown by smoke coming from the chain and/

or discoloration of the bar. Only use Bar and

Chain Oil for bar and chain lubrication.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

This engine is certified to operate on unleaded

gasoline. Before operation, gasoline must be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch Mac742 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info