Bedienungsanleitung McCulloch PRO MAC 54 54CC (Seite 10 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

478427

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

WARNING

Do not smoke when re-fuelling.

Always open the fuel cap slowly.

Re-fuel in open spaces only, keeping away from naked fla-

mes or sparks.

Always store fuel in an approved container.

SAFE STORAGE OF FUEL

Petrol is highly inflammable. Put out all cigarettes, pipes and

cigars before working with petrol. Avoid spilling petrol. Store

fuel in a cool, well ventilated place, in an approved container

specifically designed for the purpose.

Never store engine with fuel in the tank in enclosed, poorly

ventilated areas, where fuel fumes may reach an open flame,

spark or pilot light such as in a furnace, water heater, clothes

dryer etc. Petrol fumes can cause an explosion or a fire. Do

not store large amounts of fuel.

CHAIN LUBRICATION

IMPORTANT

The service life of the bar and chain depends on good lubri-

cation.

Always use chain lubricating oil of medium viscosity. We

recommend special McCulloch chain lubricating oil.

Never use waste oil for this purpose. This results in damage

to the bar, the chain and the oil pump.

Refill the chain oil tank each time the saw is refuelled.

IMPORTANT

The chain oil feed is reduced to a minimum when the regula-

ting bolt is completely closed (turning clockwise)

To prevent possible restarting problems avoid running the

fuel tank dry. This also helps to extend engine life.

NOTE: Saw chain stretches during use particularly when it

is new, and it will occasionally be necessary to adjust and

tighten it. A new chain will require adjustment after about

5 minutes of operation.

• The mechanical oil pump for chain lubrication can be

adjusted.

The feed rate of the chain oil pump can be adjusted by means

of the regulating screw (A) (see details in the illustration). The

oil feed rate is increased by turning the regulation bolt coun-

terclockwise .

IMPORTANT - The chain oil feed is reduced to a minimum

when the regulating bolt is completely closed (turning

clockwise).

STARTING AND STOPPING

IMPORTANT. Never start or operate unless bar and chain

are properly installed.

Before starting always move the saw away from the fuel-

ling area and place it on firm, flat surface, the guide bar to

the front.

STARTING COLD ENGINE

Check that the chain brake is in the disengaged position

moving the lever (L) backwards (towards the front handle).

Move the stop/run lever (A) up to the cold start position

(choke closed |

––

•|) When in the cold start position, this lever

also partially opens the throttle.

Hold the saw firmly as shown in illustration and pull the starter

rope until the engine fires once.

Once you hear the engine start, or attempt to start, move the

stop/run lever (A) to the intermediate position (choke open

––

•|| ).

ATTENTION: The throttle remains partially open in this posi-

tion and the chain may run. This allows the engine to warm

up.

Pull the starter rope until the engine starts.

Allow engine to warm up for a few seconds, holding the saw

firmly.

Beware of moving chain.

ATTENTION: Squeeze and then release the accelerator trig-

ger (B). This will allow the throttle too close and the chain

should no longer move.

STOP

To stop the engine, move the stop/run lever (A) down, to the

“STOP” position.

IMPORTANT. After lengthy use of the chain saw at full

speed, we recommend to run the engine for a few seconds at

idle speed before stopping it.

STARTING A WARM ENGINE

Leave the start/run lever (A) onto the run position (in the

middle). Pull the starter handle until the engine runs.

IMPORTANT: The automatic accelerator opening system

will only function if the start/run lever (A) is moved up to

the cold start position, and then back down to the run

position (in the middle). Do this if the engine fails to run

after starting.

STARTING A WARM ENGINE AFTER FUELLING

In the fuel tank as run completely dry, procede to start as with

a cold engine.

USAGE

IMPORTANT

Before using a chain saw read the Operator’s Manual and all

safety precautions carefully.

FELLING TREES

– Make sure that there are no bystanders or animals in the

work area.

– Study the direction of the fall of the tree and then plan your

exit path away from the planned direction of fall.

– Don’t fell trees when there is a strong wind.

1 Clear the tree base of interfering limbs and brush. Clean

the work area from stones or other objects which could

damage the chain. If the tree has large protruding roots,

remove them before felling (see illustrations).

2 A) Cut a felling notch (A) of 45°on the side you want the

tree to fall to a depth of about one third of the trunk dia-

meter (d). Then make a felling cut (B) about 5 cm higher

than the felling notch on the opposite side of the tree.

Make sure that the felling cut does not go right through

the trunk. A hinge (C) must always be left to provide

control over the direction of the fall.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch PRO MAC 54 54CC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info