Bedienungsanleitung McCulloch Promac46 II (Seite 5 von 9) (Englisch)

478411

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Ensure engine is always switched off before fitting or

adjusting chain. Wear a pair of protective gloves when

fitting or adjusting chain.

1 Ensure chain brake lever is in disengaged position (A).

Remove retaining nuts (B) and cover.

2 Turn the adjusting screw (D) counterclockwise taking it

fully back.

3 Feed chain into bar groove ensuring correct direction of

chain (P).

4 Work the chain around sprocket and set the bar as illus-

trated, make the lower hole (F) coincide with the pin (G) of

the adjusting screw.

5 Reposition side cover. Fit spike as illustrated.

6 Lock nuts (B) finger tight.

Adjust chain tension pin by turning screw (D) so that when

lifting the chain an entire drive link is just visible.

The chain is correctly tensioned when there is no slack on

the underside of the bar, and it runs freely in bar groove.

Tighten the bar retaining nuts with the wrench, pushing bar

tip upwards.

INTENZ

Turn the adjusting screw (I) counterclockwise taking it fully

back.

Feed chain into bar groove ensuring correct direction of

chain (P).

Lock nuts (B) finger tight.

Adjust chain tension pin by turning screw (I) so that when lift-

ing the chain an entire drive link is just visible.

The chain is correctly tensioned when there is no slack on the

underside of the bar, and it runs freely in bar groove. Tighten the

bar retaining nuts with the wrench, pushing bar tip upwards.

ENGLISH - 3

C. Bar and chain installation - Intenz

Do not use any other type of fuel than the type recommend-

ed in this manual.

This product is equipped with a two-stroke engine and must

therefore use a mixture of lead-free gasoline (with a minimum

of 90 octanes) and fully synthetic oil for two-stroke engines,

specific for lead-free gasoline in the proportions indicated in

the table on the cover page at item (D).

IMPORTANT! Read the oil specifications on the can careful-

ly: the use of oil lacking the specifications indicated in this

manual can cause severe damage to the engine!

To obtain the best mixture, pour the oil first, followed by

the gasoline, into an approved container, shake well

(repeat the operation every time you draw any fuel from

the container).

The characteristics of the mixture are subject to aging and

may be altered in time, so we recommend mixing only the

amount strictly needed for use. If you use a mixture that is

several weeks old, this could damage the engine.

WARNING

Do not smoke when re-fuelling.

Always open the fuel cap slowly.

Re-fuel in open spaces only, keeping away from naked

flames or sparks.

Always store fuel in an approved container.

SAFE STORAGE OF FUEL

Petrol is highly inflammable. Put out all cigarettes, pipes and

cigars before working with petrol. Avoid spilling petrol. Store

fuel in a cool, well ventilated place, in an approved container

specifically designed for the purpose. Never store engine with

fuel in the tank in enclosed, poorly ventilated areas, where fuel

fumes may reach an open flame, spark or pilot light such as in

a furnace, water heater, clothes dryer etc. Petrol fumes can

cause an explosion or a fire. Do not store large amounts of fuel.

CHAIN LUBRICATION

IMPORTANT

The service life of the bar and chain depends on good lubri-

cation. Always use chain lubricating oil of medium viscosity.

We recommend special McCulloch chain lubricating oil.

Never use waste oil for this purpose. This results in damage

to the bar, the chain and the oil pump.

Refill the chain oil tank each time the saw is refuelled.

To prevent possible restarting problems avoid running the

fuel tank dry. This also helps to extend engine life.

NOTE: Saw chain stretches during use particularly when

it is new, and it will occasionally be necessary to adjust

and tighten it. A new chain will require adjustment after

about 5 minutes of operation.

The mechanical oil pump for chain lubrication can be

adjusted.

The feed rate of the chain oil pump can be adjusted by means

of the regulating screw (A) (see details in the illustration).

6 Keep by-standers and animals out of the work area; at a

minimum distance of 10 m or twice the timber length. If

necessary, use warning signs to keep on-lookers at a dis-

tance.

Carefully survey the working site to note any hazards, eg.

roads, paths, electricity cables, dangerous trees etc. Do

not use the chainsaw if the device for stopping the chain

(safety chainbrake) does not work correctly. Never place

hands on the chain whilst the engine is running. Ensure

someone is within hearing distance in case of an accident.

If this is not possible, it is recommended that users operat-

ing chainsaws in remote areas carry an adequate first-aid kit

with them and ensure someone knows their location.

Never leave the engine running while the tool is unattend-

ed.

NEVER USE A CHAIN SAW THAT HAS FAULTY SAFE-

TY EQUIPMENT! Carry out the inspection, mainte-

nance and service routines listed in this section.

ONLY USE ORIGINAL SPARE PARTS AND ACCES-

SORIES.

D. Fuel mix

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch Promac46 II Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info