Bedienungsanleitung MCZ ALEA AIR 7 S1 (Seite 5 von 36) (Englisch)

812522

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

11-FIRST START-UP

SWITCHING THE EQUIPMENT OFF

To switch o the appliance, press the button 1 on the emergency panel or the button 3 on the optional remote control.

The equipment will start the shutdown process which involves consuming the residual pellets in the brazier, the latter being cleaned and

the residual heat in the structure being dissipated.

During the residual heat dissipation phase, the fans operate at about 80% of their output and the speed cannot be varied. This is

determined by the need for all the accumulated heat to be evacuated safely and quickly. The shutdown stage can last 15 - 30 minutes

depending on the heat stored in the structure, determined by the duration and the operating speed of the product throughout the day.

When the internal temperature drops below the set thresholds, the fans for hot air and exhaust smoke extraction will automatically

switch o.

POWER SUPPLY

When ignition is complete, the panel will display ON with a steady ame at level 3 . The following ame modulation for higher or

lower power is then controlled autonomously based on reaching the set temperature.

(also see “OPERATING MODE” - “Set Flame”)

If the ame fails to ignite, despite a regular ow of pellets, check that the brazier is seated correctly: it must rest snugly against the

interlocking slot and be clean of any ash incrustations. If no anomaly is found during this inspection, there may be a problem with

the product components or installation may not be correct.

REMOVE THE PELLETS FROM THE BRAZIER AND CONTACT AN AUTHORISED TECHNICIAN.

Please ensure the brazier is clear of ALL pellets and ash build up following any failed ignitions. Failure to clear out

the brazier prior to resetting may result in further failed ignitions or explosive ignition under certain conditions.

It is good practice to ensure eective ventilation in the room during the initial ignition, as the product will emit some

smoke and smell of paint.

Do not stand close to the product and ventilate the room as mentioned. The smell of paint will disappear after about an hour of operation,

however, it is not harmful in any case.

The product will be subject to expansion and contraction during the ignition and cooling stages, therefore slight creaking noises may be

heard.

This is perfectly normal as the structure is made of laminated steel and must not be considered a defect.

DO NOT EXPECT HEATING EFFICIENCY IMMEDIATELY!!! THE PRODUCT NEEDS SOME RUNNING-IN TIME.

Upon rst ignition, for the rst pellet hopper, it is recommended to start the stove at maximum power so that the structure and the

smell of the paint settle more quickly.

It is recommended to install cladding after the rst successful ignition.

Do not touch the product during the rst lighting, as it is during this stage that the paint sets. If you touch the paint,

you may expose the steel surface.

If required, touch up the paint with the spray can of the specic colour.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ ALEA AIR 7 S1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MCZ ALEA AIR 7 S1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info