Bedienungsanleitung MCZ AMY Air (Seite 46 von 68) (Englisch)

643531

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

9-OPERATION

Special features of AUTO-ECO mode

Once you have activated ECO-STOP and selected the temperature setpoint, if the latter is lower than the room temperature the appliance

will immediately start counting down the “ECO stop T” time.

If the setpoint is higher than the room temperature, the appliance will continue running at maximum power until it reaches the

temperature setting.

Tones (panel display: ON-OFF)

This setting disables tones sounding when the keys are pressed. It has no eect on alarm signals.

Pellet recipe - modifying the load

This function is for adapting the stove to the type of pellet in use. As there are many types of pellet available on the market, operation of

the stove can vary considerably according to the quality of the fuel. If the pellets tend to jam in the brazier due to an excess of fuel. When

the pellets clog up the brazier due to excess loading of fuel or when the ames are high even at low power, or when the ames are low, it

is possible to decrease/increase the amount of pellets in the brazier:

• Press the top right button “D” to open the menu.

• Scroll through the menus with the bottom buttons “F” and “C” until you reach the SETTINGS menu.

• Press button “D” next to the text SET.

• Scroll through the menus with the bottom buttons “F” and “C” until you reach the PELLET RECIPE menu.

• Conrm with the button “D” next to the text SET.

• Modify the value with the bottom buttons “F” and “C” which correspond to the symbols + and -.

• Conrm with the button “D” corresponding to OK.

Available values:

- 3 = Reduction of pellet loading by 20% at all power values

- 2 = Reduction of pellet loading by 13% at all power values

- 1 = Reduction of pellet loading by 6% at all power values

0 = no change

3 = Increase of pellet loading by 10% at all power values

2 = Increase of pellet loading by 6% at all power values

1 = Increase of pellet loading by 3% at all power values

Fumes evacuator fan speed variation - Var.% rpm fumes

In the event the installation presents problems in extracting smoke (lack of draft or even pressure in the duct), it is possible to increase

the smoke and ash extraction speed.

This change resolves all the potential problems related to pellets clogging in the brazier and deposits forming at the bottom of the brazier

itself caused by poor quality fuel or fuel that produces a lot of ash.

• Press the top right button “D” to access the menu.

• Scroll through the menus with the bottom buttons “F” and “C” until you reach the SETTINGS menu.

• Press button “D” next to the text SET.

• Scroll through the menus with the bottom buttons “F” and “C” until you reach the VAR. RPM FUMES menu.

• Conrm with the button “D” next to SET.

• Modify the value with the bottom buttons “F” and “C” corresponding to + and -.

• Conrm with the button “D” corresponding to OK.

The extraction speed may be altered between -30% and + 50%, with increments of 10 percent at a time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ AMY Air Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MCZ AMY Air

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info