Bedienungsanleitung MCZ AMY Air (Seite 53 von 68) (Englisch)

643531

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

11-ALARMS

Exiting the alarm conditions

To reset the alarm, hold the ON/OFF button down for a while: the stove will check to see whether the cause of the alarm is still present or

not. In the rst case, the alarm displays again, in the second case it turns OFF.

The product can be switched on again only after the cause of the fault has been denitively eliminated.

Normal shut down (panel display: shutdown)

When the shutdown key is pressed, or when there is an alarm signal, the stove enters the thermal extinguishing phase which involves

automatic execution of the following phases.

• pellet loading stops

• the room fan keeps running at the set speed so that the fumes temperature reaches 100°C, then runs at minimum speed until the

shut down temperature is reached.

• The smoke extractor fan is is activated at maximum speed and remains on for a xed period of 10 minutes, at the end of which if

the smoke T has dropped below 45°C (displayed in the INFO menu), the fan stops, otherwise it will continue to operate at minimum

speed until the temperature drops below the threshold, and then stops.

POWER FAILURE WITH STOVE ON (panel display: ACCENSIONE DOPO BLACKOUT (STARTUP AFTER POWER FAILURE)

for 10’, then ACCENSIONE (STARTUP))

In the event of a power failure, the stove does the following:

• Power failure of less than 10”: continues the work in progress;

• After a loss of power of more than 10’’ which occurred when the stove was on, or during ignition, you can restore the stove to its

previous operating condition when power returns as follows:

• 1 - Cool the system by activating the smoke extractor at minimum speed for 10’ then proceed to the next step;

• 2 - Restore the stove to the operating condition prior to the power failure.

During phase 1, the panel shows ACCENSIONE DOPO BLACKOUT (STARTUP AFTER POWER FAILURE).

During phase 2, the panel shows ACCENSIONE (STARTUP).

If during phase 1-2 the stove receives manual user commands from the control panel or remote control, it stops the blackout restoration

sequence and begins the start-up or shutdown commanded by the user.

If the stove experiences a loss of power greater than 10’’ while it is shutting down, when power is restored to the stove, it will automatically

turn on in shutdown mode, even if the smoke temperature has fallen below 45°C in the meantime. This phase can be skipped by pressing

key 0/1 (skips to start-up) and pressing it again (recognises that the stove is o).

SAFETY ALARM A05

The safety alarm includes operation of the smoke pressure switch, of the open fuel loading door and stove door.

The time between the fumes pressure switch tripping and the alarm signal is 30 seconds, after which the stove is stopped (e.g. after 30

seconds with the pellet loading hatch open, alarm A05 is tripped).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ AMY Air Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MCZ AMY Air

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info