Bedienungsanleitung MCZ Mood COMFORT AIR (Seite 52 von 72) (Englisch)

643532

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

14-ALARMS

ALARM ALERTS

In the event an operating anomaly occurs the stove starts switching o due to the alarm and informs the user of the type of

fault that has taken place via a 3 digit code which stays displayed on the rear emergency panel.

The alarm is indicated permanently by the relative 3 digit code, by a ashing red LED that lights up on the emergency panel and an

intermittent sound signal for the rst 10 minutes of the alarm. Read the instructions in the following 2 paragraphs to cancel the alarm

status and restore the normal operating mode of the stove.

The following table describes the possible alarms indicated by the stove, associated to the respective code that appears on the emergency

panel and helpful tips to solve the problem.

MESSAGE ON DISPLAY TYPE OF PROBLEM SOLUTION

A01

The ame does not light Check the level of pellets in the tank.

Check that the brazier is correctly positioned in its seat

and has no build-up or unburned material.

Make sure the ignition plug warms up.

Thoroughly empty and clean the brazier before restarting.

A02

The re goes out abnormally. Check the level of pellets in the tank.

Check that the brazier rests correctly in its seat and has no

visible deposits of unburned pellets.

A03

The temperature of the pellet hopper

exceeds the required safety threshold.

The structure overheats due to reduced

heat dissipation.

The structure is too hot because the product has been

used for too long at the maximum power or there is

poor ventilation. When the product is suciently cold,

press button B on the control panel or OFF on the remote

control to cancel alarm A03. Once the alarm is cancelled,

the product can be switched on normally.

A04

The temperature of the exhaust smoke has

exceeded certain preset safety limits.

The stove switches o automatically. Let the stove cool

down for a few minutes and then switch it on again.

Check the smoke expulsion and verify the type of pellet

used according to the instructions found in Chap. 2 of this

manual.

A05

Chimney ue clogged - wind - door open. Check the smoke duct and make sure the door is closed.

The smoke extractor fails to guarantee

sucient primary air, required for correct

combustion.

Draught diculties or brazier clogged.

Check whether the brazier is clogged and clean it, if

necessary.

Check and if necessary clean the smoke duct and air inlet.

A08

Abnormal operation of smoke fan Check cleanliness of the fumes fan compartment and

check if dirt is blocking it. If this is not enough, the smoke

fan is faulty. Contact an authorised service centre to have

it replaced.

A09

The smoke probe is faulty and does not

detect the exhaust smoke temperature

properly.

Contact an authorised service centre to have the

component replaced.

A11

Pellet supply fault Contact an authorised service centre to have the

component replaced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ Mood COMFORT AIR Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info