Bedienungsanleitung MCZ Vivo 70 Wood (Seite 9 von 42) (Englisch)

643528

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Chapter 2

INSTALLATION AND USE MANUAL

page 9

2.4. CONNECTION TO THE FLUE PIPE

The connection to the flue pipe is a very important element. The

connection must be made with a great deal of care; in the event of

erroneous or anomalous construction, it is extremely difficult to remedy

without damaging the hood liner. In addition, the connection is made in

a part of the stove where temperatures are very high, and for this

reason it is important to use materials that are capable of resisting heat

and also the acidity of the fumes produced by combustion.

Before beginning work, please note the following:

 The connecting pipe must have a maximum slope of 45

degrees. This is to avoid excessive deposit of condensation

produced in the initial phases of lighting the fireplace stove,

and/or the excessive accumulation of creosote. It also keeps

the release of smoke from being slowed down.

 The unions must be made of metal and suitable for the

specific operating conditions of the product and marked

EC (EN1856-2). The use of flexible and extending metal

pipes is not permitted.

 The components making up the connecting pipe must be

perfectly sealed.

 The joint to the flue pipe must not be too long (to avoid

obstructions), nor too short (to avoid smoke leakage).

If metal connecting pipes are used, they must be

insulated with suitable material such as ceramic fibre

matting, to avoid deterioration of the masonry and of

the decorative hood liner.

IMPORTANT!

Any increase in the section of the connecting pipe

must start immediately above the hood of the

fireplace and not along the flue pipe section.

2.5. FLUE PIPE

The flue pipe is a fundamental element in discharging smoke and

therefore must have the following requisites:

 be waterproof and thermally insulated.

 be made of suitable heat-proof materials that are resistant to

the effects of combustion products and any possible

condensation.

 have a vertical arrangement with deviations from the axis of

no more than 45° and without kinks.

 must be suitable for the specific operating conditions of the

product and marked EC (EN1856-1, EN1443).

 must be suitably sized to accommodate the draught/smoke

disposal requirements necessary for the correct functioning of

the product (EN13384-1).

 have an internal section which is preferably circular.

 be cleaned if pre-existing and has operated beforehand.

The flue pipe is of primary importance for the correct

functioning and safety of your fireplace stove.

Example of fireplace stove connection

Smoke

connection

Ceramic fibre

insulation

Flue pipe

Hood grille

45° max

Typical diagram of a correctly laid flue pipe

with a chamber including a sealed hatch to

collect and remove solid materials produced

during combustion positioned at the foot of

the external rising section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ Vivo 70 Wood Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info