Bedienungsanleitung MCZ Vivo 70 Wood (Seite 20 von 42) (Englisch)

643528

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Chapter 4

INSTALLATION AND USE MANUAL

page 20

4.5. ADJUSTMENT OF HEIGHT AND BALANCING

The VIVO fireplace stove is equipped with adjustment feet that are

screwed into the stove unit, and have the purpose of levelling the fire

bed of the fireplace stove. They are therefore provided with a minimum

adjustment. (figure 8).

To adjust the feet you must slightly raise the stove unit, grasp with the

fingers the threaded part of the screw, and loosen or tighten to allow

levelling (the adjustment is about 1 cm).

Do not eliminate the feet. They are indispensable for levelling.

Removing the feet is considered a structural modification of

the product and therefore voids the guarantee.

If the floor is made of flammable material, the lower

part of the fireplace stove must be kept at least 200

mm from the floor.

4.6. CONNECTION TO THE FLUE PIPE

We recommend connecting the stove to the flue pipe by means of pipes

and bends in aluminised steel, capable of withstanding the high

temperatures which are reached in that section of pipe, and of resisting

corrosion from the fumes. These connecting pipes are available on

request in various sizes (see our price list), and they simplify

installation, as they are assembled by fitting one into another. Figure 9

Any increase in the section of the connecting pipe

must start immediately above the hood of the

fireplace and not along the flue pipe section

When installation is complete, the smoke connection

must be insulated with ceramic fibre matting or

material that is resistant up to at least 600°C.

4.7. INSTALLATION OF CLADDING AND HOOD

LINER

BEFORE YOU START INSTALLING THE CLADDING OF

THE FIREPLACE STOVE, READ CHAPTER 5.2

“OPERATING TEST”

The fireplace stove and the parts of the cladding must be attached to

one another WITHOUT COMING INTO CONTACT WITH THE

STEEL STRUCTURE to prevent transmission of the heat to the marble

and/or stone, and to allow normal thermal dilation. use care with wood

finishes such as beams or shelves, which must be suitably insulated.

(Figure 12)

In particular, shelves must be placed at a distance of not less than 30

cm from the upper part of the unit.

We recommend making the hood liner in fire-resistant

plasterboard of 15/20 mm thickness, with a self-supporting frame in

galvanised profile, so as not put weight on components of the cladding

(such as wooden beams and marble architraves) which do not have a

load-bearing structure and to make it easy to work in the event of

future anomalies and/or maintenance.

Figure 9 – Connection to the flue pipe

THERMAL PROTECTION OF CROSSBEAM

1. Insulation applied or to be applied.

2. Wood beam

3. Marble or other material

10 mm

Figure 8 – Level adjustment feet

Figure 10 – Insulating a wooden beam

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ Vivo 70 Wood Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info