568587

ME AD 400 Seite 15

15
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
GB
ENGLISH | VISTUS-AD
15
1. Remove the two screws in order to be able to open the casing
on the outdoor station. The casing is also fitted with notches and
projections that connect the upper and lower parts of the casing.
Thus a certain amount of force is necessary in order to separate the
casing parts.
2. Position the drilling template for the outdoor station in a level
location at the intended assembly location (a spirit level is helpful
for this) and attach it with sticky tape.
3. Use the drilling template to drill the attachment holes with a 6mm
drill and insert a dowel into each hole.
4. Now remove the drilling template.
5. Feed the lines through the large hole in the outdoor station and
secure them with 4 screws.
6. Connect the line in accordance with the wiring plan.
Adjusting the nameplate
The nameplate comprises two transparent plastic parts that are
connected with 2 or 4 small screws.
7. Remove all screws from the nameplate and take the plate apart.
The foil for the name can be found between the plastic parts.
8. Write on the foil with a smudge proof felt tip pen or print a
nameplate* using a PC and printer.
9. Lay the complete nameplate (foil) between the two plastic parts
and screw them back together.
* Size of the nameplate:
VISTUS AD-4010: 71 mm x 50 mm
VISTUS AD-4020: 71 mm x 25 mm
VISTUS AD-4030: 71 mm x 15mm
10. Replace the nameplate in the front cover before re-attaching
the front cover to the outdoor station. You can attach a strip of
sticky tape over the nameplate and the casing to ensure that the
nameplate does not fall out during assembly.
Note: Remove the sticky tape from the casing immediately following
installation in order to prevent damage to the front cover!
11. Screw the front cover on using both casing screws. Please ensure
that the screws are not tilted as this can damage the thread in the
lower section of the casing.
ASSEMBLY OF THE INDOOR STATION
The installation height of the Indoor stations can be selected freely
according to your circumstances.
1. The casing on the indoor station is kept together with notches and
projections. To separate the lower section from the front section,
press a small slotted screwdriver against the snap fastener (B.15)
on the bottom side.
2. Use the lower section of the casing as an aid to mark the drill
holes. Make sure that you hold the lower section in a horizontal
position for this step.
NOTE: The lower casing section on the indoor station can also be
attached to a hollow wall box. The corresponding attachment holes
are located around the line feed hole. If this does not provide
enough hold then drill more holes and use them to also screw the
indoor station in place.
3. Drill the attachment holes with a 6 mm drill and insert one dowel
in each hole.
4. Feed the lines through the feed hole in the lower casing part
designed for this purpose and screw this down.
5. Attach the lines in accordance with the wiring plan and replace the
front casing section onto the lower casing section. Make sure that
it clicks correctly into place.
CONNECTION
An exact description of where the individual connections and terminals
are located can be found in the figures. The recommended wiring can
be seen in the corresponding wiring plan in the affix.
Connect the lines to the audio, +15V and GND on the outdoor station.
These terminals are also present on the indoor stations and need to be
connected to one another 1:1.
Note on the 2-family version: One four-pole connection terminal
is present in each residential unit. The connection terminals are numbe-
red. Connection terminal 1 is for the lower and connection terminal
2 is for the upper bell button.
Note on the 3-family version: One four-pole connection terminal
is present in each residential unit. The connection terminals are numbe-
red. Connection terminal 1 is for the lower, connection terminal 2 is for
the middle and connection terminal 3 is for the upper bell button.
Connecting the door opener
The door opener is connected directly to the outdoor station with two
lines (Figure A ‚Door opener‘). No additional power supply is necessary
in order to control the door opener. The door opener must be designed
for 12 volt DC voltage and may not require more than 0.9A of power.
In the event that the door opener needs to be correctly polarised then
both connection terminals must be marked ‘lock +’ and ‘lock –‘.
VISTUS AD-400_I-Manual_210x240_Fin8-1.indd 15 13.06.13 15:30
… 15 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

me-ad-400

Suche zurücksetzen

  • Vistus Ad 400 Klingeltöne von speicherkarte funktioniert nicht Eingereicht am 17-10-2024 14:57

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ME AD 400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info