Bedienungsanleitung ME ADV 300 (Seite 7 von 20) (Deutsch, Englisch, Holländisch, Französisch)

568508

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH | ADV-300

ADV-300 OUTDOOR UNIT FOR THE

VISTADOOR INTERCOM SYSTEM

INTRODUCTION

Thank you for choosing the VISTADOOR intercom system. You have

purchased a high quality system with a stainless steel cover. The elabo-

rate stainless steel covers are made by hand and thus have individual

characteristics that should be considered a sign of quality.

NOTES ON CARING FOR STAINLESS STEEL

Please never clean the stainless steel surfaces with standard cleaning

materials, as these are too harsh. Please simply clean using spray desi-

gned for the cleaning and care of stainless steel. If this is not available

please use only clear water.

Brushed surfaces should always be cleaned with the grain and never in

a circular motion. This will avoid the creation of scratches.

Failure to observe these notes may lead to discolouration or even to

corrosion damage in extreme cases.

The system should be assembled by a specialist.

KEY

1 Outdoor unit

1.1 Wall box

1.2 Stainless steel front plate

2 Indicator ﬁeld

4 Loudspeaker perforations

5 Bell button

6 Microphone

7 Casing screws

8 Lightness sensor

9 Volume potentiometer

10 Dip switch for the opening time of the door opener

11 Dip switch for the ID code

12 Connection terminal door opener

13 Connection terminal power supply

14 Connection terminal signal line

16 Installation aid

SCOPE OF DELIVERY

1x Outdoor unit

1x Wall box

1x Plaster aid

7x Torx screw for front plate (1pc. spare)

3x Installation aid incl. screw

8x Dowel and screw

PREPARATION FOR INSTALLATION

The following lines are required:

Single-family house: 3 lines from the outdoor unit to the indoor unit

and 2 lines from the outdoor unit to the door opener.

Multi-family house (from ADV-320): In this case 3 lines are required per

bell button from the outdoor unit into each residential unit.

Example ADV-340: 12 lines are required at the outdoor unit for the

residential units (3 lines each x 4 bell buttons) and 2 lines to

the door opener.

Up to four indoor units can be connected in parallel per residential unit.

The connection can either be laid from the indoor station or in a star

formation from a central point (distribution box).

The lines should be laid in such a way that they are fed out of the wall

directly behind the relevant outdoor/indoor unit.

Note: It is also possible to combine video and audio

components with the VISTADOOR system.

INSTALLATION OF THE OUTDOOR UNIT

The intercom system is designed to be ﬂush-mounted.

Preparation

When removing the front cover, take care that the indicator ﬁeld and

the nameplate do not fall out and get damaged.

The outdoor unit should be mounted at a height of approx. 1.5-1.6m

(middle of unit). If necessary, adjust the installation height and

location to suit the local conditions.

1. Remove the six screws from the stainless steel front plate using

a Torx screwdriver (T10) and then lift it upwards. Now you can

uncover the wall box by carefully removing the rubber seal and

taking out the actual outside station.

2. Hold the wall box straight on the wall and draw around it on the

wall with a suitable pencil. Take care that the necessary connecting

cables are in the middle part of the wall box. The cables should not

be measured too short.

3. The cable feedthrough can be detached with a sharp knife.

Note:

The hole for the intercom system should be measured so that the wall

box ﬁts precisely inside and is ﬂush with the building wall.

4. In order to anchor the wall box to the wall, ﬁrst use the holes in

the base of the wall box to mark the 8 ﬁxing holes in the wall and

then drill corresponding holes (diameter approx. 6 mm).

5. Next place the supplied dowels in the holes. The wall box can now

be afﬁxed with the 4 outer screws. Take care here to ensure that

the wall box is level; check this if necessary with a spirit level. The

wall box must also not be twisted.

NOTE: If the wall box is afﬁxed only insecurely by the screws, the

wooden frame can be ﬁlled along the sides with appropriate glue.

6. For plastering insert the supplied plaster aid into the wall box. This

prevents the wall box from being ﬁlled with mortar / plaster. When

plastering make sure that the threaded inserts will not be soiled

with mortar / plaster.

7. Insert the outer unit into the wall box. In order to prevent the outer

unit from falling out, use the supplied installation aid (16). It is

easily screwed to the wall box using one of the Torx screws and

holds the outer unit in position.

ADV-300_I-Manual_Fin1.indd 7 29.10.12 11:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ME ADV 300 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info