568514

ME ADV-F10 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
GB
ENGLISH | ADV-F10
11
1. The DECT power box must be opened before installation. No tools
are required as the casing is only clicked together. Simple press the
tab on the bottom inwards slightly and then lift the casing lid off
the box as shown in figure A1.
2. Hold the back section with one hand and mark the holes with a
suitable pen.
3. Lay the back section to one side and drill the holes
with a 6 mm drill.
4. Insert the included dowels into the holes and screw the back
section on.
5. Connect the antenna to the power box. It has a screw connection
for this purpose.
NOTE: To optimize the range, you can place the antenna at a different
location using a separately available antenna extension.
DECT indoor station
The DECT indoor station is installed in fixed position using four installa-
tion holes in the corners. The power supply is fed into the casing from
behind. Ensure correct polarity when connecting the power supply.
1. The DECT indoor station must be opened before installation. As this
casing is also only clicked together, no tools are necessary here
either. Simply press the tab on the bottom inwards slightly and
then lift the casing lid off the box as shown in figure B1.
Take care not to rip off the wires for the loudspeaker and
the microphone.
2. A drilling template is included to drill the corresponding holes to
attach the DECT indoor station. Then, align this at the installation
location, using a spirit level if necessary, and stick it to the wall
with tape.
3. Drill the holes with a 6mm drill.
4. Insert the included dowels into the holes and screw the back
section on.
Ensure that you feed the cable for the power supply to the DECT
indoor station into the casing beforehand.
OPERATION
You can connect the power once all components have been installed,
first at the outdoor station and the DECT power box and then at the
DECT indoor station.
The red power LED (4a) should then light up on the DECT power box.
On the DECT indoor station, the status LED (20) should first flash
alternately red/blue and then light permanently after a short time. The
system is then ready for operation and the bell can be activated at the
outdoor station.
Procedure
1. Press the bell button on the outdoor station
2. The blue LED (4b) on the DECT power box flashes and the indoor
station(s) play(s) the set ring melody.
3. Within 60 seconds, the press to talk button (17) can be pressed
and a conversation held with the visitor. All other indoor stations
immediately stop ringing.
4. Any door opener that is connected to the outdoor station can be
activated during the conversation by pressing the door opener
button (19).
5. To end the conversation, press the press to talk button once (17).
Note: after approximately 60 seconds, the DECT indoor station
automatically switches back to standby mode.
Set the ring melody
To hear the programmed ring tone, you can simply ring from the
outdoor station.
1. Press the button (10) to hear the next ring tone.
2. Once the tone that you wish to use is played, wait 10 seconds. The
ring tone is then programmed.
Set the volume of the ring melody
1. Open the indoor station by pressing the bottom tab on the casing a
little and pull the front casing forwards, as shown in the illustraton.
2. The volume of the ring tone is set using the potentiometer (8) on
the circuit board. Turn it in a clockwise direction to increase the
volume and in an anti-clockwise direction to reduce the volume.
NOTE: Ensure that you do not overwind the potentiometer. It can only
be turned by approx. 320°.
Deactivating the ring tone
Use the button (16) below the loudspeaker to set the ring melody to
silent, for example, so that you are not disturbed during your lunch
break. The LED under the button (21) lights up red if the ring melody
is deactivated.
Set the conversation volume on the indoor station
The potentiometer (9) on the side can be used to set the conversation
volume to any level. Turn the wheel upwards to increase the volume
and downwards to reduce it.
Alarm button
If the alarm button (11) is pressed during a conversation with the
outdoor station, then an alarm will sound at the outdoor station.
This button is without function if there is no connection to the
outdoor station.
ADV-F10_I-Manual_210x240_fin7.indd 11 12.11.13 16:57
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

me-adv-f10

Suche zurücksetzen

  • Schaltplan für klingel türöffner Anschluss an adv-100 Eingereicht am 25-7-2023 21:14

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ME ADV-F10 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info