Bedienungsanleitung ME SDO-10 (Seite 8 von 24) (Deutsch, Englisch, Holländisch, Französisch)

568515

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

SDO-10 | ENGLISH

Assembly

This device can be snapped-on to norm proﬁle rails DIN EN 50022 - 35

x 15 and DIN EN 50022 - 35 x 7.5. In order to snap the device in, hook

it in and press the top-hat rail with the nose (4) until the spring (5)

snaps into place. If it is difﬁcult to snap it in, release the spring (5) a

little with a screwdriver in the direction of the arrow.

In order to release the SDO-10 from the proﬁle rails, press the spring

with a screwdriver in the direction of the arrow and remove the SDO-10.

Connection

Connect the 4 poles of the connector terminal (2) to the four signal

lines of the door intercom system with corresponding polarity. 15V with

+15V, GND with GND, Audio with Audio and Video with Video (if the

door intercom system does not support video, the video terminal on the

SDO-10 should be left unconnected).

Connect the door opener with both terminals of the connection terminal

(3). As your door opener must be correctly polarized, the two terminals

are labeled with “+” and “-”.

Set ID code

Please note: Current to the system must be shut down in order to

change the ID code.

The SDO-10 must have the same ID code as the corresponding external

station. The external stations and the SDO-10 are set to ID 1 at the

factory so that there is no adjustment necessary here. If you have

assembled multiple external stations, the ID code of the SDO-10 must

correspond to the ID code of the external station where the door opener

is located.

The ID code is set as follows for both switches (7):

Switch 1 ON and Switch 2 ON = ID code 1

Switch 1 ON and Switch 2 OFF = ID code 2

Switch 1 OFF and Switch 2 ON = ID code 3

Switch 1 OFF and Switch 2 OFF = ID code 4

SDO-10 Assembly and start-up

Thank you for purchasing this safety door opener SDO-10 module. This

is suitable for connection to the VISTADOOR and VISTUS door intercom

systems and facilitates the control of the door opener. The SDO-10 can

also open a connected door opener within seconds after the bell is

rung. This is helpful in medical practices, for example.

Legend

1. SDO-10

2. Connector terminal to the door intercom system

3. Connector terminal to the door opener

4. Nose for top-hat rail

5. Fixing clip (spring)

6. Groove for top-hat rail

7. Switch for the ID code

8. Switch for opening

10. Power LED

ATTENTION

Do not expose this device to high temperatures, high humidity or

extreme dust.

Do not expose this device to hard blows.

Do not install this device outside.

This device must be installed by a professional.

Technical Speciﬁcations

Input: 15 Volt DC, closed-circuit current approx. 6mA (approx. 0.9 Watt)

Output: 12 Volt DC, max. 1 A

Measurements (width x height x thickness): 78mm x 92mm x 57mm

(4 TE)

SDO-10_I-Manual_210x200_Fin1.indd 8 07.05.13 13:32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ME SDO-10 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info