Bedienungsanleitung ME VD 607 (Seite 15 von 40) (Deutsch, Englisch, Holländisch, Französisch)

568583

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH | VISTUS-VD

Two-family house: Here 4 lines are required per bell button from the

outdoor unit into each residential unit. 4 lines for family 1 and 4 lines

for family 2, as well as 2 lines to the door opener.

NOTES:

1. A wiring plan can be found in the afﬁx.

2. With the VISTUS-System you can also combined video

and audio components.

Up to four indoor units can be connected in parallel per residential unit.

The connection can be laid as

1. Serial connections (from indoor station to indoor station) or as

2. Radial connections (parallel) from one central point

(distribution box).

The wiring plan in the afﬁx is base on a radial wiring

system as this is preferable.

The lines should be laid in such a way that each is fed out of the wall

directly behind the corresponding outdoor/indoor unit.

ASSEMBLY OF THE OUTDOOR STATION

The door intercom point is designed for surface mounting.

Preparation

When removing the front cover ensure that the nameplate does not fall

out and become damaged.

Also take care of the cable in the loudspeaker, which is attached in the

front part of the casing.

The camera should be ﬁtted at a height of approximately 1.5 m -1.6

m (from the centre of the camera) (Figure A). Before assembling the

door intercom you should test whether the camera shows enough of

a visitor. Adjust the assembly height and assembly location to your

circumstances as necessary.

1. Remove the two screws in order to be able to open the casing

on the outdoor station. The casing is also ﬁtted with notches and

projections that connect the upper and lower parts of the casing.

Thus a certain amount of force is necessary in order to separate the

casing parts.

2. Position the drilling template for the outdoor station in a level

location at the intended assembly location (a spirit level is helpful

for this) and attach it with sticky tape.

3. Use the drilling template to drill the attachment holes with a 6mm

drill and insert a dowel into each hole.

4. Now remove the drilling template.

5. Feed the lines through the large hole in the outdoor station and

secure them with 4 screws.

6. Connect the line in accordance with the wiring plan.

Adjusting the nameplate

The nameplate comprises two transparent plastic parts that are

connected with 2 or 4 small screws.

7. Remove all screws from the nameplate and take the plate apart.

The foil for the name can be found between the plastic parts.

8. Write on the foil with a smudge proof felt tip pen or print a

nameplate* using a PC and printer.

9. Lay the complete nameplate (foil) between the two plastic parts

and screw them back together.

* Size of the nameplate:

VISTUS VD 6X10: 71 mm x 50 mm

VISTUS VD 6X20: 71 mm x 25 mm

10. Replace the nameplate in the front cover before re-attaching

the front cover to the outdoor station. You can attach a strip of

sticky tape over the nameplate and the casing to ensure that the

nameplate does not fall out during assembly.

Note: Remove the sticky tape from the casing immediately following

installation in order to prevent damage to the front cover!

11. Screw the front cover on using both casing screws. Please ensure

that the screws are not tilted as this can damage the thread in the

lower section of the casing.

ASSEMBLY OF THE INDOOR STATION (3.5“ AND 7“)

The installation height of the Indoor stations can be selected freely

according to your circumstances.

1. The casing on the 3.5” indoor station is kept together with notches

and projections. To separate the lower section from the front

section, press a small slotted screwdriver against the snap fastener

(B.15) on the bottom side. The 7” indoor station is kept together

by 2 casing screws (C.15).

2. Use the lower section of the casing as an aid to mark the drill

holes. Make sure that you hold the lower section in a horizontal

position for this step.

NOTE: The lower casing section on the 3.5“ indoor station can also

be attached to a hollow wall box. The corresponding attachment

holes are located around the line feed hole. If this does not provide

VISTUS VD-600_I-Manual_210x240_Fin9.indd 15 10.06.13 15:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ME VD 607 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info