568579

ME VD 6320 Seite 16

16
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
VISTUS-VD | ENGLISH
16
enough hold then drill more holes and use them to also screw the
indoor station in place.
3. Drill the attachment holes with a 6 mm drill and insert one dowel in
each hole.
4. Feed the lines through the feed hole in the lower casing part
designed for this purpose and screw this down.
5. Attach the lines in accordance with the wiring plan and replace the
front casing section onto the lower casing section. Make sure that it
clicks correctly into place.
CONNECTION
An exact description of where the individual connections and terminals
are located can be found in the figures. The recommended wiring can be
seen in the corresponding wiring plan in the affix.
Connect the lines to the audio, +15V, GND and video on the outdoor
station. These terminals are also present on the indoor stations and need
to be connected to one another 1:1.
Note on the 2-family versions: One four-pole connection terminal is
present in each residential unit. The connection terminals are numbered.
Connection terminal 1 is for the lower and connection terminal 2 is for
the upper bell button.
Connecting the door opener
The door opener is connected directly to the outdoor station with two
lines (Figure A ‚Door opener‘). No additional power supply is necessary
in order to control the door opener. The door opener must be designed
for 12 volt DC voltage and may not require more than 1A of power. In
the event that the door opener needs to be correctly polarised then both
connection terminals must be marked ‘lock +’ and ‘lock –‘.
Note: In order to prevent a door opening by tampering of the outdoor
station, we recommend the installation of the separately available
security door opener module SDO-10, which is mounted in the service
entrance box. The SDO-10 is also suitable for motor locking systems and
offers several adjustable door opening times and an
auto-door-open function.
Connecting the power supply
The power supply can be connected to either the indoor or the outdoor
station. Separate spring clips are present for this purpose.
It is also possible to connect the power supply directly to the signal line
e.g. from the fuse box to the outdoor and indoor units. The power supply
unit then needs to be connection with the ground (GND) and +15V.
Open power supply unit can supply up to 8 units with power.
Connecting the external camera
An external camera can be connected to the spring clips (Figure A ‚ext
Cam‘), for example in order to be able to monitor an additional area
that is not visible on the main camera. All cameras can be connected
that require a supply voltage of 12 Volt DC and supply
an FBAS video signal.
The video line is connected to the terminal (V2) and the ground line
is connected to the terminal (GND); the supply voltage for the camera
is taken from the terminals ‘VCC2’ (positive terminal) and ‘GND’
(negative terminal).
The external camera automatically receives ID 4 (see chapter on the ID
code). When the external camera is active it is not possible to transmit
sound. The X-module on the VDV 500 XCam is not required.
Connecting a floor button
Any floor button that is present (normal closing contact) is connected
to the terminals ‘floor button’ on the indoor unit. Alternative the button
can also be connected in parallel to the lines ‘audio’ and ‘GND’. On
the two-family version please note that the correct audio line is used
(Audio1 and GND for fam. 1 and Audio2 and GND for fam. 2).
Note: If a floor button is connected then an unchangeable ring tone
is played when the floor button is activated. This ring tone is fixed
and is not included in the ‘normal’ tones/melodies to make it easy to
differentiate.
Connecting the wireless expansion model VTX-BELL
The VTX-BELL can be used to send the bell signal wirelessly to the
receiver in the BELL series (currently BELL 200 RX, BELL 210 USB and
BELL 220 RX). The wireless module will be attached to the 3-pole plug
inside the indoor station (Figures B+C). For more information please
see the VTX-BELL instructions.
POSSIBLE SETTINGS ON THE OUTDOOR STATION
The outdoor station has the following possibilities of adjusting the
system to your personal circumstances:
Volume on the outdoor station
The potentiometer (Figure A ‚Volume / Lautstärke‘) is used to set
the speaking volume on the outdoor station. For full volume turn the
potentiometer carefully in a clockwise connection until it stops and turn
it back a little. Turning the potentiometer in an anti-clockwise direction
reduces the volume.
ID code
If several outdoor stations are used in parallel (e.g. on the gate and
on the house), the DIP switch is used to set the ID code (Figure A,
VISTUS VD-600_I-Manual_210x240_Fin9.indd 16 10.06.13 15:52
… 16 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

me-vd-6320

Suche zurücksetzen

  • ist es möglich eine externe Stromversorgung für den 2. Monitor bei Eingereicht am 12-2-2019 17:54

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ME VD 6320 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info