Bedienungsanleitung Meade ETX-125AT (Seite 13 von 60) (Englisch)

470209

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

4. Place the 26mm eyepiece (12, Fig. 15) into the eyepiece holder on the

telescope and tighten the attachment thumbscrew (

13, Fig. 15) to a "firm feel" only.

Make sure that the flip-mirror control (

14, Fig. 15) is in the “up” position, as shown

in the above photo. See page 8, for more information. Remove the dust cover (

15,

Fig. 15

) from the end of the telescope tube.

5. Make sure that the computer control panel power switch (A, Fig. 2) is in the OFF

position. Remove the Autostar handbox and the coiled cord from the packing

materials. Plug one end of the cord into the HBX port (

C, Fig. 2)and the other end

of the coiled cord into the coiled cord port at the bottom of Autostar handbox, as

shown above.

6. Tighten (to a "firm feel" only, do not overtighten) the vertical lock (Fig. 6) and the hor-

izontal lock (

Fig. 9)

Attaching the Viewfinder

ETX-90AT: 8 x 21mm Viewfinder: Slide the eyepiece end of the viewfinder

through the front of the viewfinder bracket (16, Fig. 18).

ETX-105AT or ETX-125AT: 8 x 25mm Right-Angle Viewfinder: Slide the front

cell end of the right-angle viewfinder through the rear of the viewfinder bracket

(17, Fig. 19).

Unthread the six alignment screws slightly to fit the viewfinder through the

bracket. With the viewfinder in place, tighten the six alignment screws to a firm feel

only against the viewfinder tube.

Using The Viewfinder

As with most astronomical telescopes, the ETX model telescopes present a fairly

narrow field of view to the observer. As a result it is sometimes difficult to locate and

center objects in the telescope’s field of view. The viewfinder, by contrast, is a low-

power, wide-field sighting scope with crosshairs that let you easily center objects in

the eyepiece of the main telescope’s field of view. The telescope viewfinder is a great

help in locating faint astronomical objects before you begin observing through the

telescope eyepiece.

ETX-90AT 8 x 21mm Erect-Image Viewfinder:

Standard equipment with the ETX-90AT, the 8 x 21mm Erect-Image Viewfinder has

8-power magnification and an aperture of 21mm. This viewfinder presents a

correctly oriented image both up-and-down and left-to-right.

ETX-105AT or ETX-125AT 8 x 25mm Right-Angle Viewfinder:

Standard equipment with the ETX-105AT and ETX-125AT, the 8 x 25mm Right-Angle

Viewfinder has 8-power magnification and an aperture of 25mm. This viewfinder

presents a correctly oriented image up-and-down, but is reversed left-for-right.

Fig. 12: Attach telescope to

tripod.

Fig. 11: High latitude leg

mounting hole and

corresponding attachment

knob.

Fig. 10: Loosen control latch .

Fig. 15: Insert eyepiece.

Fig. 16: Tighten vertical

lock.

Fig. 17: Tighten horizontal

lock.

Fig. 13: Level tilt-plate.

Fig. 14: Handbox HBX port.

Fig. 18: ETX-90 Viewfinder Installation.

Fig. 19: ETX-105/-125 Viewfinder

ᕥ

ᕦ

ᕧ

ᕨ

ᕩ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meade ETX-125AT Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info