Bedienungsanleitung Mede8er MED500X2 (Seite 13 von 36) (Englisch)

472113

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Emergency Method (Resets Configuration to

Default)

Disconnect the power jack at the rear of the Mede8er then plug it back in - Now

press the on/off button and hold it pressed for 10 seconds and then release.

After approximately 15 seconds the LED on the Mede8er with flash blue and you will get a progress bar on

your TV display (some TV's will not display this) wait until the Mede8er re boots itself +- 60 sec. Your Mede8er

is now updated.

FIRMWARE UPDATE

WIRELESS NETWORK SETUP (basic)

The Mede8er MED500X2 is only compatible with the Mede8er Wireless Dongle 802.11n

(Other brands will not work)

Refer to User Instructions supplied with the Mede8er dongle for detailed wireless connection setup.

Power Up and hold on/off button

for 10 seconds

Only use model MED10WFB WiFi Dongle as it is supplied together with the USB extension cable base.

WIRELESS NETWORK CONNECTION

Plug the MED10WFB into the USB extension base that

was supplied with your Mede8er. Plug the USB cable

into one of the USB host ports on the side of the

Mede8er. Extend the cable and try to place the base in

a position that is away from any metal object that could

effect the RF signal strength. The best placement for

the dongle will depend on your particular environment. In order to get the best placement you may need to

extend the length with an additional USB extension cable.

Note: The draft N standard prohibits using High Throughput with WEP or WPA2-PSK as the unicast cipher,

and your data rate will drop to 54 Mbps (802.11g) which is normal. Please try other encryption methods (WPA-

PSK), or choose to configure an unsecured profile.

The operating distance or range of your wireless connection can vary significantly based on the physical

placement of the Router and the WiFi Dongle.

For best results, place your Router:

* Near the center of the area in which your Mede8er will operate,

* In an elevated location such as a high shelf,

* Away from potential sources of interference, such as PCs, microwaves, and cordless phones,

Page12

Download the latest Mede8er Firmware from www.mede8erforum.com. UnZIP or UnRAR or join with HJ Split

and will find one file named install.img. Copy this file to the root directory of a Flash Drive. Plug the flash drive

into the Mede8er.

DO NOT REMOVE POWER DURING THE EMERGENCY RECOVERY PROCEDURE.

Setup Menu Update with Auto Configuration Restore

Open the Setup Menu and select the “Misc” tab. Now select USB upgrade option. After +- 5 sec the screen

will display the current Firmware Version and the New Firmware Version. You will have the option to select

“OK” or “Cancel”. Select “OK” and the Mede8er will reboot within +- 1 second and start the update process will

start in +- 10 seconds. During the update process the front facia Blue LED will flash and you will see the

version of the Firmware and the install progress bar on your TV screen. After the update is complete the

Mede8er will reboot with the new firmware installed.

If the Mede8er does not reboot within 5 seconds

(after pressing the "Enter" button) then press the

"Home" button to initiate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mede8er MED500X2 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mede8er MED500X2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info