519071

Medion MD 15200 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
PACER menu
14
REST HR menu
17
Disposal
20
Technical data
21
SETTING menu
16
CHRONO menu
12
TIMER menu
13
MEMORY menu
15
Error recovery
18
Cleaning and care
19
• Use the ST./STP. and LP buttons to
select one of theUSER, FITNESS, FAT
BURN
or HEALTH.HLT. settings (refer to
Point 10).
The training range sets the upper and
lower limits. Please refer to Point 16 "User Heart
Rate zone" on setting your personal training range
(USER).
• To display the training watch again press the ESC
button.
The second menu CHRONO covers a stopwatch
function with lap counter. The maximum measurable
time is 99 hours 59 minutes and 59.99 seconds. It
can save up to 100 lap times.
• If necessary change to the initial display by holding
ESC for approx. 2 seconds.
• To open the
CHRONO menu press the
ST./STP. or LP button until the
Chrono(2) entry appears and select the
menu by pressing the E button.
The stopwatch is displayed.
Stopwatch
The following information can be displayed on screen:
a. Stopwatch mode
b. Minutes
c. Hours
d. Laps
e.
ST: Start by pressing ST.STP
STP: Stop by pressing ST.STP
f. LAP: Lap taking place
RST: Lap paused
g. Seconds
h. Tenth of seconds
• Start the stopwatch by pressing ST./STP..
The stopwatch starts and the message
ST changes to
STP.
• To stop the stopwatch press the ST./STP. button
again.
• To stop the lap times, whilst the stopwatch is
running press LP; to reset the stopwatch hold the LP
button for approx. 2 seconds.
The 1L message stops flashing and the current
stopped lap time is displayed whilst the stopwatch
continues in the background. After a few seconds the
display changes again to the stopwatch and the
message 2L flashes to indicate that the second lap
has started.
Display lap times
To change to the lap time memory, when the
stopwatch has stopped press E.
Use the ST./STP.
and LP buttons to view the
individual times.
CH MEM: Lap time with the supplement 1L, 2L, 3L
etc. (if no lap times were stopped this is the total time)
CH MEM TOTAL: Total stopped time
CH MEM AVERAGE: Average stopped lap time. (if no
lap times were stopped, this is the total time)
To display the stopwatch again press the ESC button
again.
The 3rd menu TIMER covers the countdown function
with preset or self-defined times. The countdown can
be set to once only or repeating.
• If necessary, you can also return to the initial display
at any time by holding down ESC for approx. 2
seconds.
• To open the
TIMER menu press the
ST./STP. or LP button until the
Timer(3) entry appears and select the
menu by pressing E.
The countdown time is displayed.
Countdown time
You can display the following information:
a. TMR-CS: Stop mode
TMR-CR: Repeat mode
b. Minutes
c. Hours
d. Time
e.
ST: Start by pressing ST./STP.
STP: Stop by pressing ST./STP.
f.
RST: Pause lap
g. Seconds
• When the timer is stopped press the LP button
repeatedly to use the preset time for the countdown.
The pre-set times are: 1 min, 5 min, 10 min, 30 min,
1h, 2h.
• Start the countdown by pressing the ST./STP.
button.
The countdown starts and the
ST display changes to
STP. At the end of each minute a beep sounds.
During the last 5 seconds of the countdown a beep
sounds each second. The end of the countdown is
indicated by a longer beep.
• To stop the countdown press the ST./STP. button
again.
• Hold down the LP button for approx. 2 seconds to
reset the countdown.
Set the timer by making entries
• When the timer is stopped hold down the E for
approx. 2 seconds. The hour digit flashes.
• Use the ST./STP. and LP buttons to
move the value up or down. Move to the
next setting by pressing E.
The minute digits flash.
• Use the ST./STP.
and LP buttons to move the value
up or down. Move to the next setting by pressing E.
The second digits flash.
• Use the ST./STP. and LP buttons to move the value
up or down. Move to the next setting by pressing E.
The timer mode flashes.
• Use the ST./STP.
and LP buttons to
select the stop mode (countdown happens
once) or the repeat mode (countdown
repeatedly starts again). After pressing
the E button the timer setting restarts
again.
Leave the menu by pressing ESC or set the timer
again.
The 4th menu PACER covers the pacemaker function.
It is possible to set a step frequency of 30 to 180
steps per minute.
• If necessary change to the initial display by holding
ESC for approx. 2 seconds.
• To open the
PACER menu press the
ST./STP. or LP button until the Pacer(4)
entry appears and select the menu by
pressing the E button.
The step counter is displayed.
Pacemaker
You can display the following information:
a. Pacemaker mode
b. Step frequency
(Steps/minute)
c. Step counter
d. ST: Start by pressing ST./STP.
STP: Stop by pressing ST./STP.
e.
RST: Pause lap
Set step counter
• When the step counter is stopped hold down the E
for approx. 2 seconds. The step frequency flashes.
• Use the ST./STP. and LP to set a step
frequency between 30 and 180 steps/
minute. Press ESC to go back to the step
counter.
• Start the step counter by pressing the
ST./STP. button.
For each step you will hear a beep and the number of
steps is indicated on the screen with
Cnt.
• Stop the step counter by pressing the ST./STP.
button again.
• Hold down the LP for approx. 2 seconds to reset
the counter.
In the fifth menu MEMORY you can view all the saved
values for heart beat and calorie consumption.
• If necessary change to the initial display by holding
ESC for approx. 2 seconds.
• To open the
MEMORY menu press the
ST./STP. or LP button until the
Memory(5) entry appears and select
the menu by pressing the E button.
The first sub-menu is shown.
5.1 Heart Rate Record
• Select the sub-menu by pressing the E button. The
last measurement is shown.
• Use the ST./STP.
and LP buttons to view the
individual measurements. The number (e. g. R-003),
date and time is given for each measurement.
• Press E to view the highest (H) and lowest
measurement (L) in succession.
• Press E again to return to the measuring results.
5.2 Calories
Select the sub-menu by pressing the E button. The
screen shows the consumption of calories or fat in the
last week (WEEKLY TOTAL).
Use the ST./STP. and LP buttons to view the
individual weeks. For each week there is a date with
week number and the calorie and fat consumption.
To record the calorie consumption you must confirm the
saving by selecting YES when leaving the TRAINING menu!
Press E repeatedly to display the following analyses in
succession:
WEEKLY TOTAL - calories burned in the week
TARGET REMAIN - remaining caloriess
AVG.CAL.PER DAY - average calories per day
AVG.CAL.PER WEEK - average calories per week
5.3 Rest Heart Rate
• Select the sub-menu by pressing the E button. The
most recently saved resting heart rate is displayed.
• Use the ST./STP. and LP buttons to view the
individual measurements. The date is shown for each
measurement.
In order to query the resting hear rate measurements at
least one measurement of the resting pulse must have been
made before in the REST HR menu.
5.4 Average Heart Rate
• Select the sub-menu by pressing the E button. The
average heart rate in the measurements of the past
week is displayed.
• Use ST./STP. and LP buttons to call up the
individual weeks. A date is shown for each
measurement.
5.5 Maximum Heart Rate
• Select the sub-menu by pressing the E button. The
highest heart rate in the measurements of the past
week is displayed.
• Use the ST./STP. and LP buttons to call up the
individual weeks. A date is shown for each
measurement.
i
i
Delete memory
• In order to delete the values in the memories, in one
of the sub-menus hold down the E button for approx.
2 seconds and then in the subsequent query use the
ST./STP. and LP buttons to select the YES entry.
• Then press the E button again for 2 seconds.
In the 6th menu SETTING you can make all the
settings for time, alarm and date as well as the clock
functions and personal data.
• If necessary change to the initial display by holding
ESC for approx. 2 seconds.
• To open the
SETTING menu press the
ST./STP. or LP button until the
Setting(6) entry appears and select
the menu by pressing the E button.
The first sub-menu is shown.
6.1 Alarm setting
• Select the sub-menu by pressing the E button. The
first alarm is displayed.
• Use the ST./STP.
and LP buttons to open the
individual alarms (Alarm1-Alarm8) and the hourly
alert.
• Press Eto switch the individual alarm or hourly alert
on or off.
• Hold down E for approx. 2 seconds to set the alarm.
The hour digit flashes.
• Use the ST./STP.
and LP buttons to adjust the
value up or down. Press E to move to the next setting.
The minute digit flashes.
• Use the ST./STP. and LP buttons to adjust the
value up or down. Press E to move to the next setting.
The alarm setting flashes.
• Use the ST./STP. and LP buttons to set the rule for
when the alarm should ring:
DAILY: Daily SUN: Sundays
MON: Mondays TUE: Tuesdays
WED: Wednesdays THU: Thursdays
FRI: Fridays SAT: Saturdays
• Then close the setting by pressing the ESC button -
the alarm is now saved.
6.2 Time Setting
- Setting time and date
Please refer to Point 8 on entering the time and date.
6.3 Dual Time Setting
- Setting the second time zone
• Select the sub-menu by pressing the E button. The
second hour digit flashes in the display.
• Use the ST./STP. and LP buttons to adjust the
value up or down. Press E to move to the next setting.
The minute digit flashes.
• Use the ST./STP. and LP buttons to adjust the
value up or down.
• Close the setting by pressing ESC - the second time
is now saved.
6.4 Personal Profile - personal data
Please refer to Point 9 on entering personal data.
6.5 Misc. settings
Set calorie target
• Select the sub-menu by pressing the E button. The
screen displays the pre-set objective of 1000 calories.
• Use the ST./STP.
and LP buttons to set the calories
to between 100 and 99900.
• The outstanding calories to the target calorie
number can be seen from the
MEMORY>CALORIES>TARGET REMAIN menu.
Set user heart rate zone
• Select the sub-menu by pressing the E button. The
training range determined from your personal data is
displayed.
• Use the ST./STP.
and LP buttons to change
between displaying percentage and heart beat.
• Press the E button to set the upper limit with the
ST./STP.
and LP buttons.
• Press the E button to set the lower limit with the
ST./STP.
and LP buttons.
• Then close the setting with the ESC - the USER
training range is now saved.
Switch key tones on/off
• Select the sub-menu by pressing the E button. The
key tone setting flashes on the screen.
• Use the ST./STP.
and LP buttons to switch
between the ON and OFF settings.
• Then leave the menu by pressing ESC to adopt the
setting.
Set LCD contrast
• Select the sub-menu by pressing the E button. The
contrast setting flashes on the screen.
• Use the ST./STP.
and LP buttons to set the
contrast to between 1 (low) and 10 (high).
• Then leave the menu by pressing ESC to adopt the
setting.
In the 7th menu
REST HR you can measure resting
heart rate and the results can then be opened in the
MEMORY>REST HEART RATE menu.
• If necessary change to the initial display by holding
ESC for approx. 2 seconds.
• To open the
REST HR menu press the
ST./STP. or LP button until the Rest
HR
(7) entry appears and select the menu
by pressing the E button.
The last resting heart rate is displayed (if
no previous measurement was made no
value is displayed).
Take the resting heart rate either immediately before
sleeping or directly after waking up.
• The resting heart rate is measured in
the same way was a normal heart rate
measurement. Press K1 and K2 until the
result of the measurement is displayed.
The measurement result is now saved and
can be viewed from the resting heart rate menu, as
stated above.
• Leave the menu again by pressing the ESC button.
i
The display is blank:
• The battery is dead. Get a watchmaker to change
the battery or contact our service.
The watch no longer responds when buttons
are pressed:
• Reset all the settings to the factory settings by
holding down the E, ST./STP. and LP buttons for 3
seconds.
The display is black:
• The ambient temperature is outside the operating
range (0° to 55°).
• Clean the watch after each training session.
• Wipe the watch with a damp cloth and mild soap so-
lution.
Only remove the battery when you want to dispose of the
watch. If you try to exchange the battery you may damage
seals or components, which results in the warranty beco-
ming void.
• To do so, loosen the 4
screws on the rear of the
device using an appropriate
screwdriver.
• Remove the battery and
dispose of the watch and
battery separately.
Be careful when removing the battery! There is a risk of in-
jury!
i
i
Battery: CR 2032
Subject to technical changes!
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Medion MD 15200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Medion MD 15200

Medion MD 15200 Bedienungsanleitung - Deutsch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info