477269
24
Zoom out
Zoom in
Vorherige Seite
1/110
Nächste Seite
16
2 Operation
GB
Adjustments on the pump unit
Spa intensity
Press the power button
once. The appliance switches on and starts operating
in the lowest mode (Low) immediately. The Low LED lights up green.
Press the power button
again. Now the Medium LED lights up green. The
appliance now operates in the medium mode (Medium).
Press the power button
a third time. Now the High LED lights up green.
The appliance now operates in the highest mode (Hi).
Press the power button
a fourth time. Now the Program LED lights up green.
The appliance now operates in the automatic interval massage program
(Program). The appliance runs through the three levels of intensity in succession
(Low, Medium, High) and then back to the beginning.
• The next time you press the power button
, the appliance switches off again.
Preset operation time
The timer button
allows you to choose between three time settings: 30, 20
or 10 minutes. It is not advisable to use the appliance for more than 30 minutes
(see safety instructions). Leave an interval of at least 30 minutes before you switch
on the appliance again.
Press the timer button
once. The operation time is set for 10 minutes. The
10 LED starts flashing yellow.
Press the timer button
once again. The operation time is set for 20 minutes.
The 20 LED starts flashing yellow.
Press the timer button
a third time. The operation time is set for 30 minutes.
The 30 LED starts flashing yellow.
Once the preset time has elapsed, the appliance switches off automatically. If no
time has been set, the appliance switches off after 30 minutes.
Switching on the heat function
NOTE
The heat function is not designed for the water temperature or
for heating up a cold bath. Warming the air created by the spa
bubbles, prevents the bath water from cooling down while it is
in use.
If you want to use the heat function, press the heat button
. The LED next to
it lights up red. Press the heat button
again to switch off the heat function and
the LED light disappears.
Adjustments on the remote control
If you want to use the infrared mode
, firstly get into the bath carefully and
switch on the appliance by pressing the power button
on the remote con-
trol.
88382_BBS_West_FINAL.qxd:Luftsprudelbad 08.10.2009 14:45 Uhr Seite 16
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Medisana BBS 88386 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info