Bedienungsanleitung Medisana Lichtwekker SAC 45100 (Seite 20 von 90) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Finnisch)

496415

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

2 Operation

Off button



If you have activated an alarm but wake up before the set time, you can press

the Off button



to turn off the alarm function. The settings of the alarm func-

tion are kept for the next day. If you do not press the Off button



e.g. if you

wake up before the alarm time and forget to press the Off button



the alarm

function is turned off automatically after about 30 minutes.

You can use Off button



to close any activated function.

Zizz button



If you are taking a short break or what to take a little nap, you can set a short-

time alarm. Press the Zizz button



, on the display



the Zizz icon appears.

Pressing the Zizz button



once sets an alarm to go off in 15 minutes. Every

time you press the button, the time until the alarm is extended by 15 minutes.

The maximum alarm time that can be set for a short-time alarm is 90 minutes.

By pressing the Set button



you confirm your entry and start the countdown

to the alarm at the same time.

In the Zizz function, the setting for sound is preset. If you need to change the

sound, use Set button



to change the setting (see “Setting the time and

alarms manually“ section, page 11-12).

Demo/Snooze/Quick Check button



If you are not using the alarm function, that is, if no alarm was activated by

Alarm button



, the button



can be used for the demo function. Press

the Demo button



. The light gets brighter in 5 second intervals (displayed

levels of brightness 0 – 20). Following that, four sounds of nature are intro-

duced. The entire demo process takes about one minute.

If an alarm has been set but the alarm is not active, you can use the button



to check the settings of the alarm function. Press the Quick Check button



and the entered values appear on the display. Press the button



again, to end

the Quick Check function.

If you have activated an alarm time, the countdown for it has already started but

the maximum level of brightness has not been reached, you can use the button



for the snooze function. Press the Snooze button



during 30 minutes and

before setting time, the wake up function (including light and sound) will stop

until the setting time. Then it takes only 1 minute for light and sound to reach

the setting degree. If you press the Snooze button



within 30 minutes after

the setting time, the unit will wake up after 5 minutes, and repeat operation

works within 30 minutes. Every time pressing the Snooze button



stops the

wake up function for further 5 minutes. The maximum to extend the alarm time

is 30 minutes.

If the device is not working correctly, pull the plug from the power point, wait

10 seconds and then plug it in again. Set the time and the other functions again

as described in the “Setting the time and alarms manually“ section, page

11-12.

2.4

Reset function

GA_SAC_West_Final_neu.qxd:Lichtwecker 15.10.2008 12:17 Uhr Seite 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Medisana Lichtwekker SAC 45100 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info