Bedienungsanleitung Medisana MS 2000 (Seite 15 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Finnisch)

790487

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

3 Operating GB

Overview of all buttons on the remote control (advanced functions):

t Button for manual selection of the massage method:

Switch through in the following order: Kneading, tapping, swedish,

shiatsu, clapping, roll massage, end function.

r + f + g (only with manually selected massage activated):

r Change the direction/rhythm of the massage

g Change the speed of the back massage in ve steps

f For tapping, clapping, shiatsu, roll massage: Change the distance bet-

ween the massage heads in 3 steps.

uspot massage/partial back massage:

Spot massage at the current point on the back.

Press the button again to switch to partial back massage.

z/d Up/Down: Adjust massage position individually

s Heating function

1. button press = activation at knee/leg

2. button press = activation at knee/leg + massage heads

3. button press = switch off the heating function

i Air pressure massage of the whole body (automatic mode): on/off

oManual selection of air pressure massage areas:

Leg support -> Arm support -> Shoulders -> Off

p Adjust the intensity of the air pressure massage in 5 steps

(works in automatic and manual mode)

a Switch foot massage roller on and off

3.4 Switching off the device

Press the Power button 9 on the remote control.

All functions are terminated - but the massage heads are still moving to

their parking position. Wait a few seconds.

Then set the on/off switch (position 7) to position „O“ and disconnect the

device from the power socket.

3.5 Troubleshooting

problem possible cause suggestion

The device does not

work

The device is not plug-

ged in properly

Ensure the voltage

on the device corre-

sponds to the local

mains voltage and

then plug in again.

Make sure the outlet is

properly working.

The device stopped

working

The device has just

nished its auto timer

session and has auto-

matically switched to

standby mode.

If you want another

session, press the

power button again.

The device stopped

working

You may have used

the device continuous-

ly for 45 minutes

where the over-heat

protection has been

activated.

Unplug the device and

let it cool down for 60

minutes before you

use it again.

The device stopped

working

An excessive load has

been applied on the

device.

Reduce the excessive

load and start again.

The device is abnor-

mally warm

The device is likely to

be overused.

Unplug the device and

let it cool down before

using it again.

Noise can be heard

from the device

Noise is made by the

mechanical parts of

the device.

This is normal and

does not mean that

the device is faulty.

If the problem encountered is not listed, please try the following suggestions:

1. Turn off the product and unplug it.

2. Wait for 60 minutes.

3. Plug the product back to the recommended outlet and restart.

4. If the problem persists, contact the authorized service center.

The service centre address is shown on the attached leaet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Medisana MS 2000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info