Bedienungsanleitung Medisana TargetScale 3 - 40413 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

689892

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

TargetScale 3 Instruction Manual GB

B) Setting the personal data in the scales / Weighing with body analysis

The scales can store the data (gender, athlete mode, height, age) for 8 people with up to 30 memory locations each. The values preset in the

scales are: Male, 165 cm, 30 years old, kg.

Press the ON/OFF sensor button

shortly.

Select desired memory location

with buttons "+" and "-".

Memory location "P0" is used for

"guest mode". No data will be saved

when using "P0".

Press "OK" to conrm your selection.

Now the symbols for gender/

athletic condition are ashing.

Select with "+" or "-" and con-

rm with "OK".

Enter your height, age and your

target weight. Change numbers

by pressing "+" and "-". Conrm

every step with "OK".

Displays shows "- - - - -" and

then "0.0 kg".

Stand on the scales barefoot

(without socks or similar).

Your weight is shown.

Then body analysis is conducted.

After a few seconds the display

shows the following measure-

ments:

• Actual weight

• Dierence between actual

weight and target weight

(see

Target weight function)

• BMI

• KCAL (caloric needs)

• Proportion body fat

• Proportion muscle mass

• Proportion body water

• Bone mass

A) Weighing with “step-on”-function

Simply stand on the scales bare-

foot (without socks or similar).

Your weight is shown.

Before you can use the scale, pull the insulating

strip out of the battery compartment on the un-

derside of the scale.

Make sure the scales are on a rm, level surface. If

you only want to weigh yourself but have moved the

scales just before, you must rst initialise the scales.

To do this, press your foot on the middle of the surface

of the scales. "0.0 kg" appears in the display.

When the scales switch o, they are ready for the

“step-on” function.

2 2

Automatic user recognition based on last measurement:

Stand on the scales barefoot. Your user data (memory location) is

selected automatically.

• If your user data is not selected correctly , select the number

(P1 to P8) by pressing "+" or "-" and conrm with "OK".

Automatic user recognition

Target weight function

Three shining rings indicate how close you are to

your target weight:

If dierence between actual weight and target

weight is +/- 0 to 1.5 kg, inner ring is shining.

Within +/- 1.5 to 3 kg the middle ring is shining.

Above 3 kg dierence the outer ring is shining.

Change the unit of weight

You may have your weight displayed in kilograms (kg), pounds (lb)

or stones (st). Turn on the scales. When the display shows „0.0“,

select the unit (KG / LB / ST:LB) by pressing "+" or "-".

If you have already saved your

personal data before, steps 3, 4 and

5 do not apply. After selecting a

memory location the stored data is

shown one after another.

Proceed with step 6.

...

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Medisana TargetScale 3 - 40413 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info